DYNAMIC RADAR CRUISE CONTROL SYSTEM, Diagnostic DTC:P0571

DTC Code DTC Name
P0571 Brake Switch "A" Circuit

DESCRIPTION

Condition 1:


Condition 2:


DTC No. Detection Item DTC Detection Condition Trouble Area
P0571 Brake Switch "A" Circuit

Condition 1:


  • w/o Full-speed range following function:

    While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, the hybrid vehicle control ECU receives a stop light control ECU assembly malfunction signal from the skid control ECU (brake booster with master cylinder assembly) for approximately 0.5 seconds or more.

  • w/ Full-speed Range Following Function:

    While the vehicle speed is 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, the hybrid vehicle control ECU receives a stop light control ECU assembly malfunction signal from the skid control ECU (brake booster with master cylinder assembly) for approximately 0.5 seconds or more.

Condition 2:


  • w/o Full-speed range following function:

    While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, voltage of STP terminal and that of ST1- terminal of hybrid vehicle control ECU are less than 1 V for approximately 0.5 seconds or more.

  • w/ Full-speed Range Following Function:

    While the vehicle speed is 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, voltage of STP terminal and that of ST1- terminal of hybrid vehicle control ECU are less than 1 V for approximately 0.5 seconds or more.

Condition 1:


  • Skid control ECU (brake booster with master cylinder assembly)

  • Stop light control ECU assembly

  • Stop light switch assembly

  • Rear combination light assembly LH

  • Rear combination light assembly RH

  • Rear light assembly LH

  • Rear light assembly RH

  • Center stop light assembly

  • Hybrid vehicle control ECU

  • Shift lock control unit assembly

  • Certification ECU (smart key ECU assembly)

  • Harness or connector

Condition 2:


  • Stop light switch assembly

  • Stop light control ECU assembly

  • Harness or connector

  • Hybrid vehicle control ECU

WIRING DIAGRAM

B002HEWE02
B002JK5E01

CAUTION / NOTICE / HINT

Note


  • Before replacing the certification ECU (smart key ECU assembly), refer to smart entry and start system (for Entry Function) Precaution.

    Click here

  • Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.

  • First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

    Click here

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR


    1. Disconnect the A60 and A61 hybrid vehicle control ECU connector.

      B002KASC02
      *a Brake pedal depressed *b Brake pedal released
      *c

      Rear view of wire harness connector

      (to hybrid vehicle control ECU)

      - -
    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A61-28 (ST1-) - Body ground Brake pedal depressed 0 to 1.5 V
      Brake pedal released 7.5 to 14 V
      A60-15 (STP) - Body ground Brake pedal depressed 7.5 to 14 V
      Brake pedal released 0 to 1.5 V
      Result
      Proceed to
      OK
      NG

    NG
    OK
  2. INSPECT TERMINAL VOLTAGE (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) CONNECTOR)


    1. Turn the power switch off.

    2. B002K8EC52
      *a

      Front view of wire harness connector

      (to Skid control ECU (brake booster with master cylinder assembly))

      Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A57-6 (STP2) - Body ground Brake pedal depressed 11 to 14 V
      Brake pedal released Below 1.5 V
      A57-3 (STPO) - Body ground Power switch on (IG) 11 to 14 V
      A57-33 (STP) - Body ground Brake pedal depressed 11 to 14 V
      Brake pedal released Below 1.5 V
    4. Connect the skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Result Proceed to
      All terminal voltage is normal A
      Only STP terminal voltage abnormal B
      Only STPO terminal voltage abnormal C
      Only STP2 terminal voltage abnormal D
      STPO terminal and STP2 terminal voltage abnormal E

    B
    C
    D
    E
    A
  3. PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)


    1. Turn the power switch off.

    2. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    3. Perform "Active Test" according to the display on the GTS.

      Click here


      Chassis > ABS/VSC/TRC > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Stop Light Relay Stop light control ECU assembly ECU (Relay) ON/OFF

      Stop lights come on

      Vehicle condition: Vehicle stopped


      Chassis > ABS/VSC/TRC > Active Test
      Tester Display
      Stop Light Relay
      OK
      Stop light turns ON/OFF in response to the GTS operation
      Result
      Proceed to
      OK
      NG

    NG
    OK
  4. CHECK FOR DTC (RADAR CRUISE 1)


    1. Clear the DTCs.

      Click here


      Powertrain > Radar Cruise1 > Clear DTCs
    2. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    3. Perform "Active Test" according to the display on the GTS.

      Click here


      Chassis > ABS/VSC/TRC > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Stop Light Relay Stop light control ECU assembly ECU (Relay) ON/OFF

      Stop lights come on

      Vehicle condition: Vehicle stopped


      Chassis > ABS/VSC/TRC > Active Test
      Tester Display
      Stop Light Relay
    4. Check for DTCs.

      Click here


      Powertrain > Radar Cruise1 > Trouble Codes
      Result
      Result Proceed to
      DTC P0571 is not output. A
      DTC P0571 is output. B

    A
    B
  5. INSPECT SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)


    1. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    2. Perform "Active Test" according to the display on the GTS.

      Click here


      Chassis > ABS/VSC/TRC > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Stop Light Relay Stop light control ECU assembly ECU (Relay) ON/OFF

      Stop lights come on

      Vehicle condition: Vehicle stopped


      Chassis > ABS/VSC/TRC > Active Test
      Tester Display
      Stop Light Relay
    3. B002HYNC34
      *a Component with harness connected (Stop Light Control ECU Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A3-9 (ACC) - Body ground Active Test is ON Below 1.5 V
      Result
      Proceed to
      OK
      NG

    OK
    NG
  6. INSPECT TERMINAL VOLTAGE (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) CONNECTOR)


    1. Turn the power switch off.

    2. B002K8EC53
      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

      Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A57-33 (STP) - Body ground Brake pedal released Below 1.5 V
    4. Connect the skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    NG
    OK
  7. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)


    1. Turn the power switch off.

    2. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Disconnect the A60 hybrid vehicle control ECU connector.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A57-35 (STP) or A60-15 (STP) - Body ground Brake pedal depressed 11 to 14 V
    5. Connect the A60 hybrid vehicle control ECU connector.

    6. Connect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    OK
    NG
  8. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)


    1. Turn the power switch off.

    2. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Disconnect the A60 hybrid vehicle control ECU connector.

    4. Disconnect the I22 shift lock control unit assembly connector.

    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A57-33 (STP) or I22-4 (STP) - Body ground Brake pedal depressed 11 to 14 V
    6. Disconnect the I22 shift lock control unit assembly connector.

    7. Disconnect the A60 hybrid vehicle control ECU connector.

    8. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    OK
    NG
  9. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))


    1. Turn the power switch off.

    2. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Disconnect the A60 hybrid vehicle control ECU connector.

    4. Disconnect the I22 shift lock control unit assembly connector.

    5. Disconnect the I51 certification ECU (smart key ECU assembly) connector.

    6. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A57-33 (STP) or I51-2 (STP1) - Body ground Brake pedal depressed 11 to 14 V
    7. Connect the I51 certification ECU (smart key ECU assembly) connector.

    8. Connect the I22 shift lock control unit assembly connector.

    9. Connect the A60 hybrid vehicle control ECU connector.

    10. Connect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    OK
    NG
  10. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - VEHICLE APPROACHING SPEAKER CONTROLLER)


    1. Turn the power switch off.

    2. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Disconnect the A60 hybrid vehicle control ECU connector.

    4. Disconnect the I22 shift lock control unit assembly connector.

    5. Disconnect the I51 certification ECU (smart key ECU assembly) connector.

    6. Disconnect the A67 vehicle approaching speaker controller connector.

    7. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A57-33 (STP) or A67-2 (STP) - Body ground Brake pedal depressed 11 to 14 V
    8. Connect the A67 vehicle approaching speaker controller connector.

    9. Connect the I51 certification ECU (smart key ECU assembly) connector.

    10. Connect the I22 shift lock control unit assembly connector.

    11. Connect the A60 hybrid vehicle control ECU connector.

    12. Connect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    OK
    NG
  11. CHECK WIRE HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)


    1. Turn the power switch off.

    2. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Disconnect the A60 hybrid vehicle control ECU connector.

    4. Disconnect the I22 shift lock control unit assembly connector.

    5. Disconnect the I51 certification ECU (smart key ECU assembly) connector.

    6. Disconnect the A67 vehicle approaching speaker controller connector.

    7. Disconnect the A1 stop light switch assembly connector.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A1-2 (L) or A57-33 (STP) - Body ground Always 10 kΩ or higher
    9. Connect the A1 stop light switch assembly connector.

    10. Connect the A67 vehicle approaching speaker controller connector.

    11. Connect the I51 certification ECU (smart key ECU assembly) connector.

    12. Connect the I22 shift lock control unit assembly connector.

    13. Connect the A60 hybrid vehicle control ECU connector.

    14. Connect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    NG
    OK
  12. INSPECT STOP LIGHT SWITCH ASSEMBLY


    1. Inspect the stop light switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK
    NG
  13. CHECK WIRE HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - STOP LIGHT CONTROL ECU ASSEMBLY)


    1. Turn the power switch off.

    2. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Disconnect the A60 hybrid vehicle control ECU connector.

    4. Disconnect the I22 shift lock control unit assembly connector.

    5. Disconnect the I51 certification ECU (smart key ECU assembly) connector.

    6. Disconnect the A67 vehicle approaching speaker controller connector.

    7. Disconnect the A1 stop light switch assembly connector.

    8. Disconnect the A3 stop light control ECU assembly connector.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A3-5 (STP) or A57-33 (STP) - Body ground Always 10 kΩ or higher
    10. Connect the A3 stop light control ECU assembly connector.

    11. Connect the A1 stop light switch assembly connector.

    12. Connect the A67 vehicle approaching speaker controller connector.

    13. Connect the I51 certification ECU (smart key ECU assembly) connector.

    14. Connect the I22 shift lock control unit assembly connector.

    15. Connect the A60 hybrid vehicle control ECU connector.

    16. Connect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    NG
    OK
  14. INSPECT STOP LIGHT CONTROL ECU ASSEMBLY


    1. Inspect the stop light control ECU assembly.

      for LHD: Click here

      for RHD: Click here

      Result
      Proceed to
      OK
      NG

    OK
    NG
  15. INSPECT STOP LIGHT SWITCH ASSEMBLY


    1. Inspect the stop light switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK
    NG
  16. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - STOP LIGHT CONTROL ECU ASSEMBLY)


    1. Turn the power switch off.

    2. Disconnect the A3 stop light control ECU assembly.

    3. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A57-3 (STPO) - A3-9 (ACC) Always Below 1 Ω
    5. Connect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    6. Connect the A3 stop light control ECU assembly.

      Result
      Proceed to
      OK
      NG

    NG
    OK
  17. CHECK STOP LIGHT CONTROL ECU ASSEMBLY


    1. Turn the power switch off.

    2. B002IYCC29
      *a

      Front view of wire harness connector

      (to Stop Light Control ECU Assembly)

      Disconnect the stop light control ECU assembly connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A3-6 (+B) - Body ground Always 11 to 14 V
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A3-8 (GND) - Body ground Always Below 1 Ω
    5. Connect the stop light control ECU assembly connector.

      Result
      Proceed to
      OK
      NG

    OK
    NG
  18. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - STOP LIGHT CONTROL ECU ASSEMBLY)


    1. Turn the power switch off.

    2. Disconnect the A3 stop light control ECU assembly.

    3. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A57-33 (STP) - A3-5 (STP) Always Below 1 Ω
    5. Connect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    6. Connect the A3 stop light control ECU assembly.

      Result
      Proceed to
      OK
      NG

    NG
    OK
  19. INSPECT TERMINAL VOLTAGE (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) CONNECTOR)


    1. Turn the power switch off.

    2. B002K8EC54
      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

      Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A57-6 (STP2) - Body ground Brake pedal released Below 1.5 V
    4. Connect the skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    NG
    OK
  20. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - REAR COMBINATION LIGHT ASSEMBLY LH)


    1. Turn the power switch off.

    2. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Disconnect the Q16 rear combination light assembly LH connector.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A57-6 (STP2) or Q16-2 (STP) - Body ground Brake pedal depressed 11 to 14 V
    5. Connect the Q16 rear combination light assembly LH connector.

    6. Connect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    OK
    NG
  21. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - REAR COMBINATION LIGHT ASSEMBLY RH)


    1. Turn the power switch off.

    2. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Disconnect the Q16 rear combination light assembly LH connector.

    4. Disconnect the P13 rear combination light assembly RH connector.

    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A57-6 (STP2) or P13-2 (STP) - Body ground Brake pedal depressed 11 to 14 V
    6. Connect the P13 rear combination light assembly RH connector.

    7. Connect the Q16 rear combination light assembly LH connector.

    8. Connect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    OK
    NG
  22. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - REAR LIGHT ASSEMBLY LH)


    1. Turn the power switch off.

    2. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Disconnect the Q16 rear combination light assembly LH connector.

    4. Disconnect the P13 rear combination light assembly RH connector.

    5. Disconnect the Y11 rear light assembly LH connector.

    6. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A57-6 (STP2) or Y11-3 (B) - Body ground Brake pedal depressed 11 to 14 V
    7. Connect the Y11 rear light assembly LH connector.

    8. Connect the P13 rear combination light assembly RH connector.

    9. Connect the Q16 rear combination light assembly LH connector.

    10. Connect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    OK
    NG
  23. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - REAR LIGHT ASSEMBLY RH)


    1. Turn the power switch off.

    2. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Disconnect the Q16 rear combination light assembly LH connector.

    4. Disconnect the P13 rear combination light assembly RH connector.

    5. Disconnect the Y11 rear light assembly LH connector.

    6. Disconnect the Y10 rear light assembly RH connector.

    7. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A57-6 (STP2) or Y10-3 (B) - Body ground Brake pedal depressed 11 to 14 V
    8. Connect the Y10 rear light assembly RH connector.

    9. Connect the Y11 rear light assembly LH connector.

    10. Connect the P13 rear combination light assembly RH connector.

    11. Connect the Q16 rear combination light assembly LH connector.

    12. Connect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    OK
    NG
  24. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - CENTER STOP LIGHT ASSEMBLY)


    1. Turn the power switch off.

    2. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Disconnect the Q16 rear combination light assembly LH connector.

    4. Disconnect the P13 rear combination light assembly RH connector.

    5. Disconnect the Y11 rear light assembly LH connector.

    6. Disconnect the Y10 rear light assembly RH connector.

    7. Disconnect the e1 center stop light assembly connector.

    8. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A57-6 (STP2) or e1-2 (B2) - Body ground Brake pedal depressed 11 to 14 V
    9. Connect the e1 center stop light assembly connector.

    10. Connect the Y10 rear light assembly RH connector.

    11. Connect the Y11 rear light assembly LH connector.

    12. Connect the P13 rear combination light assembly RH connector.

    13. Connect the Q16 rear combination light assembly LH connector.

    14. Connect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    OK
    NG
  25. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - STOP LIGHT CONTROL ECU ASSEMBLY)


    1. Turn the power switch off.

    2. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Disconnect the Q16 rear combination light assembly LH connector.

    4. Disconnect the P13 rear combination light assembly RH connector.

    5. Disconnect the Y11 rear light assembly LH connector.

    6. Disconnect the Y10 rear light assembly RH connector.

    7. Disconnect the e1 center stop light assembly connector.

    8. Disconnect the A3 stop light control ECU assembly connector.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A3-1 (OUT) - A57-6 (STP2) Always Below 1 Ω
      A3-1 (OUT) or A57-6 (STP2) - Body ground Always 10 kΩ or higher
    10. Connect the A3 stop light control ECU assembly connector.

    11. Connect the e1 center stop light assembly connector.

    12. Connect the Y10 rear light assembly RH connector.

    13. Connect the Y11 rear light assembly LH connector.

    14. Connect the P13 rear combination light assembly RH connector.

    15. Connect the Q16 rear combination light assembly LH connector.

    16. Connect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    OK
    NG
  26. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - STOP LIGHT CONTROL ECU ASSEMBLY)


    1. Turn the power switch off.

    2. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Disconnect the A3 stop light control ECU assembly.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A57-6 (STP2) or A3-1 (OUT) - Body ground Brake pedal released Below 1.5 V
    5. Connect the A3 stop light control ECU assembly.

    6. Connect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    OK
    NG
  27. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - REAR COMBINATION LIGHT ASSEMBLY LH)


    1. Turn the power switch off.

    2. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Disconnect the A3 stop light control ECU assembly.

    4. Disconnect the Q16 rear combination light assembly LH connector.

    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A57-6 (STP2) or Q16-2 (STP) - Body ground Brake pedal released Below 1.5 V
    6. Connect the Q16 rear combination light assembly LH connector.

    7. Connect the A3 stop light control ECU assembly.

    8. Connect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    OK
    NG
  28. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - REAR COMBINATION LIGHT ASSEMBLY RH)


    1. Turn the power switch off.

    2. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Disconnect the A3 stop light control ECU assembly.

    4. Disconnect the Q16 rear combination light assembly LH connector.

    5. Disconnect the P13 rear combination light assembly RH connector.

    6. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Tester Connection Specified Condition
      A57-6 (STP2) or P13-2 (STP) - Body ground Brake pedal released Below 1.5 V
    7. Connect the P13 rear combination light assembly RH connector.

    8. Connect the Q16 rear combination light assembly LH connector.

    9. Connect the A3 stop light control ECU assembly.

    10. Connect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    OK
    NG
  29. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - REAR LIGHT ASSEMBLY LH)


    1. Turn the power switch off.

    2. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Disconnect the A3 stop light control ECU assembly.

    4. Disconnect the Q16 rear combination light assembly LH connector.

    5. Disconnect the P13 rear combination light assembly RH connector.

    6. Disconnect the Y11 rear light assembly LH connector.

    7. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A57-6 (STP2) or Y11-3 (B) - Body ground Brake pedal released Below 1.5 V
    8. Connect the Y11 rear light assembly LH connector.

    9. Connect the P13 rear combination light assembly RH connector.

    10. Connect the Q16 rear combination light assembly LH connector.

    11. Connect the A3 stop light control ECU assembly.

    12. Connect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    OK
    NG
  30. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - REAR LIGHT ASSEMBLY RH)


    1. Turn the power switch off.

    2. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Disconnect the A3 stop light control ECU assembly.

    4. Disconnect the Q16 rear combination light assembly LH connector.

    5. Disconnect the P13 rear combination light assembly RH connector.

    6. Disconnect the Y11 rear light assembly LH connector.

    7. Disconnect the Y10 rear light assembly RH connector.

    8. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A57-6 (STP2) or Y10-3 (B) - Body ground Brake pedal released Below 1.5 V
    9. Connect the Y10 rear light assembly RH connector.

    10. Connect the Y11 rear light assembly LH connector.

    11. Connect the P13 rear combination light assembly RH connector.

    12. Connect the Q16 rear combination light assembly LH connector.

    13. Connect the A3 stop light control ECU assembly.

    14. Connect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    OK
    NG
  31. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - CENTER STOP LIGHT ASSEMBLY)


    1. Turn the power switch off.

    2. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Disconnect the A3 stop light control ECU assembly.

    4. Disconnect the Q16 rear combination light assembly LH connector.

    5. Disconnect the P13 rear combination light assembly RH connector.

    6. Disconnect the Y11 rear light assembly LH connector.

    7. Disconnect the Y10 rear light assembly RH connector.

    8. Disconnect the e1 center stop light assembly connector.

    9. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A57-6 (STP2) or e1-2 (B2) - Body ground Brake pedal released Below 1.5 V
    10. Connect the e1 center stop light assembly connector.

    11. Connect the Y10 rear light assembly RH connector.

    12. Connect the Y11 rear light assembly LH connector.

    13. Connect the P13 rear combination light assembly RH connector.

    14. Connect the Q16 rear combination light assembly LH connector.

    15. Connect the A3 stop light control ECU assembly.

    16. Connect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    OK
    NG
  32. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) - STOP LIGHT CONTROL ECU ASSEMBLY)


    1. Turn the power switch off.

    2. Disconnect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Disconnect the A3 stop light control ECU assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A57-3 (STPO) or A3-9 (ACC) - Body ground Always 10 kΩ or higher
    5. Connect the A3 stop light control ECU assembly connector.

    6. Connect the A57 skid control ECU (brake booster with master cylinder assembly) connector.

      Result
      Proceed to
      OK
      NG

    OK
    NG
  33. CHECK STOP LIGHT SWITCH ASSEMBLY


    1. Turn the power switch off.

    2. B002KPJC38
      *a

      Front view of wire harness connector

      (to Stop Light Switch Assembly)

      Disconnect the stop light switch assembly connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A1-1 (B) - Body ground Always 11 to 14 V
      A1-5 (B) - Body ground Power switch on (IG) 11 to 14 V
      A1-5 (B) - Body ground Power switch off Below 1 V
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A1-3 (GND) - Body ground Always Below 1 Ω
    5. Connect the stop light switch assembly connector.

      Result
      Proceed to
      OK
      NG

    NG
    OK
  34. INSPECT STOP LIGHT SWITCH ASSEMBLY


    1. Inspect the stop light switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG
    OK
  35. CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)


    1. Turn the power switch off.

    2. Disconnect the A1 stop light switch assembly connector.

    3. Disconnect the A60 and A61 hybrid vehicle control ECU connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A60-15 (STP) - A1-2 (L) Always Below 1 Ω
      A61-28 (ST1-) - A1-4 (L) Always Below 1 Ω
      A60-15 (STP) or A1-2 (L) - Body ground Always 10 kΩ or higher
      A61-28 (ST1-) or A1-4 (L) - Body ground Always 10 kΩ or higher
    5. Connect the A60 and A61 hybrid vehicle control ECU connector.

    6. Connect the A1 stop light switch assembly connector.

      Result
      Proceed to
      OK
      NG

    OK
    NG