AIRBAG SYSTEM DTC CHECK / CLEAR


  1. CHECK FOR DTCs (USING SST CHECK WIRE)

    A01KFIIE18

    1. Check for DTCs (present trouble code).


      1. Turn the ignition switch to ON, and wait approximately 60 seconds.

      2. Using SST, connect Terminals 4 (CG) and 13 (TC) of the DLC3.

        SST
        09843-18040

        Note

        Connect the SST to the correct terminals of the DLC3 to avoid a malfunction.

    2. Check for DTCs (past trouble code).


      1. Using SST, connect Terminals 4 (CG) and 13 (TC) of the DLC3.

        SST
        09843-18040

        Note

        Connect the SST to the correct terminals of the DLC3 to avoid a malfunction.

      2. Turn the ignition switch to ON, and wait for approximately 60 seconds.

    3. A01KI73E05

      Read the DTCs.


      1. Read the DTCs from the blinking patterns of the SRS warning light. The following blinking patterns (normal system codes (with and without past trouble codes) and DTCs 11 and 31) are shown in the illustration as examples.


        • Normal system code indication (without past trouble code)

          The light blinks twice per second.

        • Normal system code indication (with past trouble code)

          If a past trouble code is stored in the airbag ECU assembly, the light blinks once per second.

        • DTC indication

          The codes are indicated using a number of blinking and interval time, as a two-digits number. A figure in the digit is shown by a number of blinking with a 0.5 second interval. A 1.5 second interval occurs between the digit indications. If there are two or more DTCs, a 2.5 second interval occurs between the code indications. When all codes have been indicated, the light remains off for 4.0 seconds, and then repeats the indication of all the codes.

        Tech Tips


        • Since the code uses hexadecimal number, the numbers of blinks that correspond to the letters A to F of the hexadecimal numbers are as shown in the following table.

          Hexadecimal number Number of blinking
          A 10
          B 11
          C 12
          D 13
          E 14
          F 15
        • If there are two or more DTCs, the smaller code comes first.

        • If DTCs are indicated without connecting the terminals, refer to the Problem Symptom Table Click here.

        • If the SRS warning light does not show any blinking pattern, even when the terminals are connected, refer too the Problem Symptom Table Click here.

  2. CLEAR DTC (USING SST CHECK WIRE)


    1. When the ignition switch is turned off, the DTCs are cleared.

      Tech Tips

      Some DTCs cannot be cleared by using the method shown above.

    2. Using SST, connect Terminals 13 (TC) and 4 (CG) of the DLC3, and then turn the ignition switch to ON.

      SST
      09843-18040
    3. Disconnect Terminal 13 (TC) of the DLC3 within 10 seconds of the start of the indication of the DTCs. Check that the SRS warning light comes on approximately 3 seconds later.

    4. Connect Terminal 13 (TC) of the DLC3 within 2 to 4 seconds of the SRS warning light coming on. Check that the SRS warning light goes off approximately 3 seconds later.

    5. Disconnect Terminal 13 (TC) of the DLC3 within 2 to 4 seconds of the SRS warning light going out. Check that the SRS warning light comes on again approximately 3 seconds later.

    6. Connect Terminal 13 (TC) of the DLC3 within 2 to 4 seconds of the SRS warning light coming on. Check that the SRS warning light goes off approximately 3 seconds later. Also check that the normal system code is indicated within 1 second.

      Tech Tips

      If the DTCs have not been completely cleared, repeat this procedure until they have all been cleared.

      A01KGBNE01
  3. CHECK FOR DTCs (USING INTELLIGENT TESTER)

    A01KI6BE04

    1. Turn the ignition switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Enter the following menus: Body / SRS Airbag / DTC.

    5. Check for DTCs by following the prompts on the tester screen.

      Tech Tips

      Refer to the intelligent tester operator's manual for further details.

  4. CLEAR DTCs (USING INTELLIGENT TESTER)


    1. Turn the ignition switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Enter the following menus: Body / SRS Airbag / DTC / Clear.

    5. Clear the DTCs by following the prompts on the tester screen.

      Tech Tips

      Refer to the intelligent tester operator's manual for further details.