CHECK REAR WHEEL CYLINDER FLUID PRESSURE
Set the rear axle load.
| Standard | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Install the SST to the front and rear wheel cylinders.
Bleed the air from the brake system.
Measure the rear wheel cylinder fluid pressure.
Raise the front wheel cylinder fluid pressure to 6.9 MPa (70.4 kgf/cm2) by pressing the brake pedal, and measure the rear wheel cylinder fluid pressure.
| Standard | ||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Raise the front wheel cylinder fluid pressure to 11.8 MPa (120.3 kgf/cm2) by pressing the brake pedal, and measure the rear wheel cylinder fluid pressure.
| Standard | ||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Note
The pedal should not be depressed twice or released while the front wheel cylinder fluid pressure is being set.
Read the value of the rear wheel cylinder fluid pressure after adjusting and holding the front wheel cylinder fluid pressure for 2 seconds.
If the result is not as specified, adjust the load sensing proportioning valve.
Calculate the rear wheel cylinder fluid pressure in accordance with the procedure below when the rear axle load can not be adjusted to the specified axle weight.
Measure the rear axle load.
Calculate the fluid pressure crossover point at the measured rear axle load by applying the following formula.
| Fluid pressure crossover point |
|---|
| P = (Cp - Bp) / (Cw - Bw) x (W - Bw) + Bp |
| P (MPa) | Fluid pressure crossover point at "W" |
| W (kN) | Measured rear axle load |
| Cp (MPa) | Fluid pressure crossover point at "C" |
| Bp (MPa) | Fluid pressure crossover point at "B" |
| Cw (kN) | Rear axle load at "C" |
| Bw (kN) | Rear axle load at "B" |
| ABC point data table | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Calculate the rear wheel cylinder fluid pressure when front wheel cylinder fluid pressure is 6.9 MPa (70.4 kgf/cm2) in the following formula.
| Rear wheel cylinder fluid pressure formula | ||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
| Service limit |
|---|
| +/- 0.59 MPa (+/- 6.0 kgf/cm2) |
If the result is not as specified, adjust the load sensing proportioning valve.
Example:
| Vehicle Model | LY225R-TBMDS |
| Measured Rear Axle Load | 9.8 kN (1000 kgf) |
| Front Wheel Cylinder Fluid Pressure | 6.9 MPa (70.4 kgf/cm2) |
| Standard (ABC point data table) | ||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
||||||||||||||||||
| Fluid pressure crossover point |
|---|
| P = (Cp - Bp) / (Cw - Bw) x (W - Bw) + Bp |
| P (MPa) | Fluid pressure crossover point at "W" |
| W (kN) | Measured rear axle load |
| Cp (MPa) | Fluid pressure crossover point at "C" |
| Bp (MPa) | Fluid pressure crossover point at "B" |
| Cw (kN) | Rear axle load at "C" |
| Bw (kN) | Rear axle load at "B" |
| Rear wheel cylinder fluid pressure |
|---|
| P + (6.9 - P) x 0.2 |
P = (6.5 - 3.1) / (15.8 - 7.8) x (9.8 - 7.8) + 3.1
P = 3.95 MPa
Rear wheel cylinder fluid pressure = 3.95 + (6.9 - 3.95) x 0.2
Rear wheel cylinder fluid pressure = 4.5 MPa (45.9 kgf/cm2)
ADJUST LOAD SENSING PROPORTIONING VALVE
Adjust the length of the No. 2 load sensing spring shackle.
| *1 | Lock Nut |
Low pressure - Lengthen A
High pressure - Shorten A
| Initial set |
|---|
| 78 mm (3.07 in.) |
| Adjusting |
|---|
| 72 to 84 mm (2.83 to 3.31 in.) |
Tech Tips
One turn of the No. 2 shackle nut changes the fluid pressure to about the following specifications.
| Standard | ||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Tighten the lock nut.
If the pressure cannot be adjusted by the No. 2 load sensing spring shackle, raise or lower the load sensing proportioning valve.
Low pressure - Lower
High pressure - Raise
Tighten the nuts.
Adjust the length of the No. 2 load sensing spring shackle again.
If it cannot be adjusted, inspect the load sensing proportioning valve.
Remove the SST.
Bleed the air from the brake system.
Check for brake fluid leakage.