BRAKE ACTUATOR ON-VEHICLE INSPECTION


  1. INSPECT ACTUATOR OPERATION (In case of using the Intelligent Tester)


    1. Connect the intelligent tester.


      1. Connect the intelligent tester to the DLC3.

      2. Start the engine and run it at idle.

      3. Select the ACTIVE TEST mode on the intelligent tester.

        Tech Tips

        Please refer to the intelligent tester operators manual for further details.

    2. Inspect the actuator motor operation.


      1. With the motor relay ON, check the actuator motor operation noise.

      2. Turn the motor relay OFF.

      3. Depress the brake pedal and hold it for about 15 seconds. Check that the brake pedal cannot be depressed.

      4. With the motor relay ON, check that the pedal does not pulsate.

        Note

        Do not keep motor relay ON for more than 5 seconds continuously. When operating it continuously, set the interval of more than 20 seconds.

      5. Turn the motor relay OFF and release the brake pedal.

    3. Inspect the right front wheel operation.

      Note

      Never turn ON the solenoid which is not described below.


      1. With the brake pedal depressed, perform the following operations.

      2. Turn the SFRH and SFRR solenoid ON simultaneously, and check that the pedal cannot be depressed.

        Note

        Do not keep solenoid ON for more than 10 seconds continuously. When operating it continuously, set the interval of more than 20 seconds.

      3. Turn the SFRH and SFRR solenoid OFF simultaneously, and check that the pedal can be depressed.

      4. Turn the motor relay ON, and check that the pedal returns.

        Note

        Do not keep motor relay ON for more than 5 seconds continuously. When operating it continuously, set the interval of more than 20 seconds.

      5. Turn the motor relay OFF and release the brake pedal.

    4. Inspect other wheel operations.

      As in the same procedure, check the solenoids of other wheels.

      Tech Tips

      Left front wheel: SFLH, SFLR

      Rear wheel: SRH, SRR

    5. Clear the DTC Click here

  2. INSPECT ACTUATOR OPERATION (In case of not using the Intelligent Tester)

    Tech Tips

    Using the Brake actuator checker (SST), check the operation of the actuator. If the actuator does not operate, check the operation of sub-wire harness G according to the instructions on Click here and Click here . If the solenoid and/or pump motor relay are abnormal, replace the relay and inspect the actuator operation again.


    1. Inspect battery voltage.

      Battery voltage
      10 - 14 V
    2. Disconnect the 2 connectors from the brake actuator.

    3. Connect the actuator checker (SST) to the brake actuator.


      1. Connect the actuator checker (SST) to the actuator, control relay and body side wire harness through the sub-wire harness G, I and L (SST) as shown.

        SST
        09990-00150
        09990-00250
        09990-00300
        09990-00360
      2. Connect the red cable of the checker to the battery positive (+) terminal and black cable to the negative (-) terminal. Connect the black cable of the sub-wire harness to the battery negative (-) terminal or body ground.

        A01KES0E01
        Text in Illustration
        *1 ABS Actuator *2 Sub-Wire Harness G (SST)
        *3 Sub-Wire Harness L (SST) *4 Sub-Wire Harness I (SST)
        *a Body Ground - -
    4. A01KHD3

      Inspect the brake actuator operation of the front RH wheel.

      Tech Tips

      The functions of the actuator checker switches are shown in the table below.

      A Motor ON/OFF
      B Front LH solenoid ON/OFF
      C -
      D Front RH solenoid
      E -
      F Rear solenoid
      G Solenoid ON/OFF

      1. Start the engine and run it at idle.

      2. Turn select switch of the actuator checker to the "D" position.

      3. Push and hold in the "A" switch for a few seconds. Make sure that you can hear the motor running.

      4. A01KI6T

        Depress the brake pedal and hold it until step 7 is completed.

      5. Push and hold in the "G" push switch for a few seconds, and check that the brake pedal does not go down.

        Note

        Do not keep the "G" push switch pushed down for more than 10 seconds.

      6. Release the "G" push switch and check that the pedal goes down.

      7. A01KF6P

        Push the "A" switch and check that the pedal returns.

      8. Release the brake pedal.

      9. A01KFR3

        Push and hold in the "A" switch for a few seconds.

      10. Depress the brake pedal and hold it for about 15 seconds. As you hold the pedal down, push the "A" switch for a few seconds and check that the brake pedal does not pulsate.

      11. Release the brake pedal.

    5. A01KIE6

      Inspect the operation for rear wheel.


      1. Turn the select switch to the "F" position.

      2. Repeat 3 to 11 of the step (d), checking the actuator operation similarly.

    6. Inspect the operation for front wheel.

      Tech Tips

      Push the "B" switch instead of the "G" switch, and inspect it in any selector switch position.


      1. Push and hold "A" switch for a few seconds.

      2. A01KHQF

        Depress the brake pedal and hold it until step (5) is completed.

      3. Push and hold in the "B" switch for a few seconds, and check that the brake pedal does not go down.

        Note

        Do not keep the "B" switch pushed down for more than 10 seconds.

      4. Release the "B" switch and check that the pedal goes down.

      5. A01KIEN

        Push the "A" switch and check that the pedal returns.

      6. Release the brake pedal.

      7. A01KIKG

        Push and hold in the "A" switch for a few seconds.

      8. Depress the brake pedal and hold it for about 15 seconds. As you hold the pedal down, push the "A" switch for a few seconds and check that the brake pedal does not pulsate.

      9. Release the brake pedal.

    7. A01KHD3

      Push the "A" switch.


      1. Push and hold in the "A" switch for a few seconds.

      2. Stop the engine.

    8. Disconnect the actuator checker (SST) and 3 sub-wire harness (SST) from the actuator.

      SST
      09990-00150
      09990-00250
      09990-00300
      09990-00360
    9. Connect 2 connectors to the actuator.