INSPECT 1ST GEAR THRUST CLEARANCE
Using a feeler gauge, check the thrust clearance of the 1st gear.
| Standard clearance |
|---|
| 0.20 to 0.45 mm (0.0079 to 0.0177 in.) |
INSPECT 2ND GEAR THRUST CLEARANCE
Using a feeler gauge, check the thrust clearance of the 2nd gear.
| Standard clearance |
|---|
| 0.10 to 0.25 mm (0.0039 to 0.0098 in.) |
INSPECT 3RD GEAR THRUST CLEARANCE
Using a feeler gauge, check the thrust clearance of the 3rd gear.
| Standard clearance |
|---|
| 0.10 to 0.25 mm (0.0039 to 0.0098 in.) |
INSPECT 1ST GEAR RADIAL CLEARANCE
Using a dial indicator, check the radial clearance of the 1st gear.
| Standard clearance |
|---|
| 0.020 to 0.073 mm (0.0008 to 0.0029 in.) |
If the clearance is out of the specification, replace the 1st gear needle roller bearing with a new one.
INSPECT 2ND GEAR RADIAL CLEARANCE
Using a dial indicator, check the radial clearance of the 2nd gear.
| Standard clearance |
|---|
| 0.015 to 0.068mm (0.0006 to 0.0027 in.) |
If the clearance is out of the specification, replace the 2nd gear needle roller bearing with a new one.
INSPECT 3RD GEAR RADIAL CLEARANCE
Using a dial indicator, check the radial clearance of the 3rd gear.
| Standard clearance |
|---|
| 0.015 to 0.068 mm (0.0006 to 0.0027 in.) |
If the clearance is out of the specification, replace the 3rd gear needle roller bearing with a new one.
REMOVE 1ST GEAR
Using SST and a press, remove the 5th gear, output shaft center bearing, 1st gear thrust washer and the 1st gear from the output shaft.
REMOVE SYNCHRONIZER RING NO.1 (FOR FIRST SYNCHRONIZER RING)
Remove the synchronizer ring No. 1 (for 1st synchronizer ring) from the output shaft.
REMOVE 1ST GEAR THRUST WASHER PIN OR BALL
Remove the 1st gear thrust washer pin (ball) from the output shaft.
REMOVE 1ST GEAR NEEDLE ROLLER BEARING
Remove the 1st gear needle roller bearing from the output shaft.
REMOVE 1ST GEAR BEARING SPACER
Remove the 1st gear bearing spacer from the output shaft.
REMOVE BEARING SHAFT SNAP RING
Using 2 screwdrivers and a hammer, remove the bearing shaft snap ring from the output shaft.
Note
Cover with a piece of cloth so that the shaft snap ring will not fly up.
REMOVE 2ND GEAR
Using SST and a press, remove the transmission clutch hub No. 1, synchronizer ring No. 1, reverse gear and the second gear from the output shaft.
REMOVE 2ND GEAR NEEDLE ROLLER BEARING
Remove the 2nd gear needle roller bearing from the output shaft.
REMOVE REVERSE GEAR
Remove the reverse gear, 3 synchromesh shifting keys No. 1 and the 3 synchromesh shifting key No. 1 compression springs.
Note
Cover with a piece of cloth so that the shifting key and the compression spring will not fly up.
REMOVE CLUTCH HUB SET SHAFT SNAP RING
Using a snap ring expander, remove the clutch hub shaft snap ring from the output shaft.
Note
Do not damage the sliding surface of the bearing.
REMOVE 3RD GEAR
Using SST and a press, remove the No. 2 synchronizer ring, transmission hub sleeve No. 2 assembly and the 3rd gear from the output shaft.
REMOVE 3RD GEAR NEEDLE ROLLER BEARING
Remove the 3rd gear needle roller bearing from the output shaft.
REMOVE TRANSMISSION HUB SLEEVE NO.2
Remove the transmission hub sleeve No. 2, and remove the 2 synchromesh shifting key springs No. 2 and the 3 synchromesh shifting keys No. 2 from the transmission clutch hub No. 2.