GENERATOR (w/ DPF) REASSEMBLY


  1. INSTALL GENERATOR DRIVE END FRAME BEARING


    1. A01KGXD

      Using SST and a press, press in a new bearing.

      SST
      09950-60010   ( 09951-00470 )
      09950-70010   ( 09951-07100 )
    2. A01KIGSE02
      Text in Illustration
      *1 Claw

      Align the claws of the bearing retainer with the grooves inside the drive end frame.

    3. Install the bearing retainer with the 4 screws.

      Torque:
      2.3 N*m  { 23 kgf*cm, 20 in.*lbf }
  2. INSTALL GENERATOR ROTOR ASSEMBLY


    1. Install the rotor and washer to the drive end frame.

  3. INSTALL GENERATOR COIL ASSEMBLY


    1. A01KGNEE02
      Text in Illustration
      *a Deep socket wrench (21 mm)

      Using deep socket wrench (21 mm) and a press, slowly press in the generator coil assembly.

    2. A01KF83

      Install the generator coil assembly with the 4 through bolts.

      Torque:
      5.9 N*m  { 60 kgf*cm, 52 in.*lbf }
  4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY


    1. A01KH7BE06
      Text in Illustration
      *1 Pin

      While pushing the 2 brushes to the inside of the generator brush holder assembly, insert a φ1.0 mm (0.039 in.) pin into the generator brush holder hole.

    2. A01KGNLE03
      Text in Illustration
      *1 Pin

      Install the brush holder assembly with the 2 screws.

      Torque:
      1.8 N*m  { 18 kgf*cm, 16 in.*lbf }
    3. Pull out the pin from the brush holder assembly.

  5. INSTALL TERMINAL INSULATOR


    1. A01KFLY

      Install the terminal insulator.

  6. INSTALL GENERATOR REAR END COVER


    1. A01KEE9

      Install the generator rear end cover with the 3 nuts.

      Torque:
      4.6 N*m  { 47 kgf*cm, 41 in.*lbf }
  7. INSTALL GENERATOR WITH CLUTCH PULLEY


    1. Install the pulley by hand.

    2. Mount generator in a vise between aluminum plates.

    3. A01KIIWE01

      Install SST (A) and (B) to the generator with clutch pulley as shown in the illustration.

      SST
      09820-63021

      Note

      Securely attach SST to the generator with clutch pulley and generator rotor shaft.

    4. A01KHVYE01
      Text in Illustration
      *a Hold
      *b Turn
      *c Fulcrum Length

      Turn SST (B) counterclockwise, and tighten the pulley.

      SST
      09820-63021
      Torque:
      without SST
      111 N*m  { 1127 kgf*cm, 81 ft.*lbf }
      with SST
      88 N*m  { 897 kgf*cm, 65 ft.*lbf }

      Tech Tips


      • Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). When using a torque wrench with a fulcrum length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification Click here.


      • Make sure SST and the wrench are connected in a straight line.

      Note

      Be careful as the generator with clutch pulley or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.

    5. Remove SST from the generator.

    6. Check that the generator pulley rotates smoothly.

    7. Install a new generator pulley cap.