CYLINDER HEAD INSPECTION

Tech Tips


  • Thoroughly clean all parts to be assembled.

  • Before installing the parts, apply fresh engine oil to all sliding and rotating surfaces.

  • Replace all gaskets and oil seals with new ones.


  1. INSPECT CYLINDER HEAD SUB-ASSEMBLY


    1. A01KGGCE01
      Text in Illustration
      *a Cylinder Block Side
      *b Intake Manifold Side
      *c Exhaust Manifold Side

      Inspect for flatness.


      1. Using a precision straight edge and feeler gauge, measure the surfaces contacting the cylinder block and the manifolds for warpage.

        Maximum warpage
        0.15 mm (0.0059 in.)

        If warpage is greater than maximum, replace the cylinder head.

    2. A01KFMM

      Inspect for cracks.


      1. Using a dye penetrant, check the combustion chamber, intake ports, exhaust ports and cylinder block surface for cracks.

        If cracked, replace the cylinder head.

  2. INSPECT INTAKE VALVE


    1. A01KIDE

      Using a micrometer, measure the diameter of the valve stem.

      Valve stem diameter
      5.970 - 5.985 mm (0.2350 - 0.2356 in.)
    2. A01KGX4E01
      Text in Illustration
      *a Valve Face Angle

      Check the valve face angle.


      1. Grind the valve enough to remove pits and carbon.

      2. Check that the valve is ground to the correct valve face angle.

        Valve face angle
        44.5°
    3. A01KEGXE01
      Text in Illustration
      *a Margin Thickness

      Check the valve head margin thickness.

      Standard margin thickness
      1.1 mm (0.043 in.)
      Minimum margin thickness
      0.6 mm (0.024 in.)

      If the margin thickness is less than minimum, replace the valve.

    4. A01KIIME01
      Text in Illustration
      *1 Overall Length

      Check the valve overall length.

      Standard overall length
      105.38 - 105.78 mm (4.1488 - 4.1646 in.)
      Minimum overall length
      104.88 mm (4.1291 in.)

      If the overall length is less than minimum, replace the valve.

    5. A01KFO0

      Check the surface of the valve stem tip for wear.

      If the valve stem tip is worn, resurface the tip with a grinder or replace the valve.

      Note

      Do not grind off more than minimum.

  3. INSPECT EXHAUST VALVE


    1. A01KIDE

      Using a micrometer, measure the diameter of the valve stem.

      Valve stem diameter
      5.960 - 5.975 mm (0.2346 - 0.2352 in.)
    2. A01KGX4E01
      Text in Illustration
      *a Valve Face Angle

      Check the valve face angle.


      1. Grind the valve enough to remove pits and carbon.

      2. Check that the valve is ground to the correct valve face angle.

        Valve face angle
        44.5°
    3. A01KEGXE01
      Text in Illustration
      *a Margin Thickness

      Check the valve head margin thickness.

      Standard margin thickness
      1.1 mm (0.043 in.)
      Minimum margin thickness
      0.6 mm (0.024 in.)

      If the margin thickness is less than minimum, replace the valve.

    4. A01KIIME01
      Text in Illustration
      *1 Overall Length

      Check the valve overall length.

      Standard overall length
      105.57 - 105.97 mm (4.1563 - 4.1720 in.)
      Minimum overall length
      105.07 mm (4.1366 in.)

      If the overall length is less than minimum, replace the valve.

    5. A01KFO0

      Check the surface of the valve stem tip for wear.

      If the valve stem tip is worn, resurface the tip with a grinder or replace the valve.

      Note

      Do not grind off more than minimum.

  4. INSPECT INNER COMPRESSION SPRING


    1. A01KHK3E01
      Text in Illustration
      *a Deviation

      Using a steel square, measure the deviation of the spring.

      Maximum deviation
      2.0 mm (0.079 in.)

      If the deviation is greater than maximum, replace the spring.

    2. A01KIR8E01
      Text in Illustration
      *a Blue Mark or None

      Using vernier calipers, measure the free length of the spring.

      Free length
      Blue mark 46.8 mm (1.843 in.)
      None 46.5 mm (1.831 in.)

      If the free length is not as specified, replace the spring.

    3. A01KGMJ

      Using a spring tester, measure the tension of the valve spring at the specified installed length.

      Installed tension (at 33.1 mm (1.303 in.))
      Blue mark 149.9 - 166.1 N (15.3 - 16.9 kgf, 33.7 - 37.3 lbf)
      None 150.2 - 165.8 N (15.3 - 16.9 kgf, 33.7 - 37.3 lbf)

      If the installed tension is not as specified, replace the spring.

  5. INSPECT INTAKE VALVE GUIDE BUSH


    1. A01KEOH

      Using a caliper gauge, measure the inside diameter of the guide bush.

      Bush inside diameter
      6.010 - 6.030 mm (0.2366 - 0.2374 in.)
    2. Subtract the valve stem diameter measurement (See step 2) from the guide bush inside diameter measurement.

      Standard oil clearance
      0.025 - 0.060 mm (0.0010 - 0.0024 in.)
      Maximum oil clearance
      0.08 mm (0.0031 in.)

      If the clearance is greater than maximum, replace the valve and guide bush.


  6. INSPECT EXHAUST VALVE GUIDE BUSH


    1. A01KHI4

      Using a caliper gauge, measure the inside diameter of the guide bush.

      Bush inside diameter
      6.010 - 6.030 mm (0.2366 - 0.2374 in.)
    2. Subtract the valve stem diameter measurement (See step 3) from the guide bush inside diameter measurement.

      Standard oil clearance
      0.035 - 0.070 mm (0.0014 - 0.0028 in.)
      Maximum oil clearance
      0.10 mm (0.0039 in.)

      If the clearance is greater than maximum, replace the valve and guide bush.


  7. INSPECT INTAKE VALVE SEATS


    1. A01KF1L

      Using a 45° carbide cutter, resurface the valve seats. Remove only enough metal to clean the seats.

    2. A01KF8RE01
      Text in Illustration
      *a Width

      Check the valve seating position.


      1. Apply a light coat of prussian blue (or white lead) to the valve face.

      2. Lightly press the valve against the seat. Do not rotate valve.

    3. Check the valve face and seat for the following:


      1. If blue appears 360° around the face, the valve is concentric. If not, replace the valve.

      2. If blue appears 360° around the valve seat, the guide and face are concentric. If not, resurface the seat.

      3. Check that the seat contact is in the middle of the valve face with the width:

        Width
        1.2 - 1.6 mm (0.047 - 0.063 in.)
  8. INSPECT EXHAUST VALVE SEATS


    1. A01KESB

      Using a 45° carbide cutter, resurface the valve seats. Remove only enough metal to clean the seats.

    2. A01KEC9E01
      Text in Illustration
      *a Width

      Check the valve seating position.


      1. Apply a light coat of prussian blue (or white lead) to the valve face.

      2. Lightly press the valve against the seat. Do not rotate valve.

    3. Check the valve face and seat for the following:


      1. If blue appears 360° around the face, the valve is concentric. If not, replace the valve.

      2. If blue appears 360° around the valve seat, the guide and face are concentric. If not, resurface the seat.

      3. Check that the seat contact is in the middle of the valve face with the width:

        Width
        1.6 - 2.0 mm (0.063 - 0.079 in.)
  9. INSPECT VALVE LIFTER


    1. A01KG9C

      Using a micrometer, measure the lifter diameter.

      Lifter diameter
      30.966 - 30.976 mm (1.2191 - 1.2195 in.)
    2. A01KFRY

      Using a caliper gauge, measure the lifter bore diameter of the cylinder head.

      Lifter bore diameter
      31.000 - 31.021 mm (1.2205 - 1.2213 in.)
    3. Subtract the lifter diameter measurement from the lifter bore diameter measurement.

      Standard oil clearance
      0.024 - 0.055 mm (0.0009 - 0.0022 in.)
      Maximum oil clearance
      0.075 mm (0.0030 in.)

      If the oil clearance is greater than maximum, replace the lifter. If necessary, replace the cylinder head.

  10. INSPECT CAMSHAFT (for Intake Side)


    1. A01KING

      Inspect the circle runout.


      1. Place the camshaft on V-blocks.

      2. Using a dial indicator, measure the circle runout at the center journal.

        Maximum circle runout
        0.06 mm (0.0024 in)

        If the circle runout is greater than maximum, replace the camshaft.

    2. A01KI98

      Using a micrometer, measure the cam lobe height.

      Standard cam lobe height
      46.830 - 46.930 mm (1.8437 - 1.8476 in.)
      Minimum cam lobe height
      46.68 mm (1.8378 in.)

      If the cam lobe height is less than minimum, replace the camshaft.

    3. A01KGBY

      Inspect the journal diameter of the camshaft.


      1. Using a micrometer, measure the journal diameter of the camshaft for the camshaft bearing.

        Journal diameter
        27.969 - 27.985 mm (1.1011 - 1.1018 in.)

        If the journal diameter is not as specified, check the oil clearance.

    4. A01KGRXE01

      Check the oil clearance.


      1. Clean the bearing caps and journals.

        Text in Illustration
        *1 Plastigage
      2. Check that bearings for flaking and scoring.

        If the bearings are damaged, replace the bearing caps and cylinder head as a set.

      3. Install the bearings to the bearing caps and cylinder head.

      4. Place the camshaft on the cylinder head.

      5. Lay a strip of Plastigage across each of the journals.

      6. A01KFOP

        Install the bearing caps Click here.

        Note

        Do not turn the camshaft.

      7. Remove the bearing caps.

      8. A01KGKNE01
        Text in Illustration
        *1 Plastigage

        Measure the Plastigage at its widest point.

        Standard oil clearance
        0.025 - 0.062 mm (0.0010 - 0.0024 in.)
        Maximum oil clearance
        0.10 mm (0.0039 in.)

        If the oil clearance is greater than maximum, replace the camshaft. If necessary, replace the bearing cap and cylinder head as a set.

      9. Completely remove the Plastigage.

      10. Remove the camshaft.

    5. A01KH94

      Check the thrust clearance.


      1. Install the camshaft Click here.

      2. Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

        Standard thrust clearance
        0.035 - 0.185 mm (0.0014 - 0.0073 in.)
        Maximum thrust clearance
        0.25 mm (0.0098 in.)

        If the thrust clearance is greater than maximum, replace the camshaft. If necessary, replace the bearing cap and cylinder head as a set.

    6. A01KGTO

      Check the gear backlash.


      1. Install the 2 camshafts Click here.

      2. Using a dial indicator, measure the backlash.

        Standard backlash
        0.035 - 0.145 mm (0.0014 - 0.0057 in.)
        Maximum backlash
        0.189 mm (0.0074 in.)

        If the backlash is greater than maximum, replace the 2 camshafts.

      3. Remove the 2 camshafts.

  11. INSPECT NO.2 CAMSHAFT (for Exhaust Side)


    1. A01KH8K

      Inspect the circle runout.


      1. Place the camshaft on V-blocks.

      2. Using a dial indicator, measure the circle runout at the center journal.

        Maximum circle runout
        0.06 mm (0.0024 in)

        If the circle runout is greater than maximum, replace the camshaft.

    2. A01KI98

      Using a micrometer, measure the cam lobe height.

      Standard cam lobe height
      46.870 - 46.970 mm (1.8453 - 1.8492 in.)
      Minimum cam lobe height
      46.72 mm (1.8394 in.)

      If the cam lobe height is less than minimum, replace the camshaft.

    3. A01KGBY

      Inspect the journal diameter of the camshaft.


      1. Using a micrometer, measure the journal diameter of the camshaft for the camshaft bearing.

        Journal diameter
        27.969 - 27.985 mm (1.1011 - 1.1018 in.)

        If the journal diameter is not as specified, check the oil clearance.

    4. A01KFK4E01

      Check the oil clearance.


      1. Clean the bearing caps and journals.

        Text in Illustration
        *1 Plastigage
      2. Check that bearings for flaking and scoring.

        If the bearings are damaged, replace the bearing caps and cylinder head as a set.

      3. Install the bearings to the bearing caps and cylinder head.

      4. Place the camshaft on the cylinder head.

      5. Lay a strip of Plastigage across each of the journals.

      6. A01KHZN

        Install the bearing caps Click here.

        Note

        Do not turn the camshaft.

      7. Remove the bearing caps.

      8. A01KGZWE01
        Text in Illustration
        *1 Plastigage

        Measure the Plastigage at its widest point.

        Standard oil clearance
        0.025 - 0.062 mm (0.0010 - 0.0024 in.)
        Maximum oil clearance
        0.10 mm (0.0039 in.)

        If the oil clearance is greater than maximum, replace the camshaft. If necessary, replace the bearing cap and cylinder head as a set.

      9. Completely remove the Plastigage.

      10. Remove the camshaft.

    5. A01KFF3

      Check the thrust clearance.


      1. Install the camshaft Click here.

      2. Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

        Standard thrust clearance
        0.035 - 0.185 mm (0.0014 - 0.0073 in.)
        Maximum thrust clearance
        0.25 mm (0.0098 in.)

        If the thrust clearance is greater than maximum, replace the camshaft. If necessary, replace the bearing cap and cylinder head as a set.