ECD SYSTEM (w/ EGR Cooler Bypass Valve) Lack of Power or Hesitation

DESCRIPTION

Malfunction Condition Main Trouble Area Related Trouble Area

  • Lack of power caused by abnormal fuel injection volume (supply pump malfunction or injector malfunction)

  • Lack of power caused by intake air volume shortage (turbocharger malfunction, or front exhaust pipe or exhaust manifold converter blocked)

(a) Injector malfunctions


  • Injector sliding malfunction

  • Injector stuck closed

  • Injector stuck open

  • Deposits in fuel injector assembly

  • Injector circuit malfunction

(b) Abnormal common rail pressure


  • Suction control valve

(c) Abnormal intake air volume


  • Turbocharger sub-assembly

  • Front exhaust pipe blockage

  • Exhaust manifold converter blockage


  • Pressure discharge valve (P1271 set simultaneously)

  • Intake air system leakage

  • Intake air system blockage

  • EGR system

  • Fuel filter element is clogged

  • Throttle valve

  • Compression pressure

  • Injector compensation code

  • Fuel leak

  • Glow plug assembly

  • Fuel pressure sensor

  • Manifold absolute pressure sensor

  • Vacuum hose connection for Manifold absolute pressure sensor

  • Mass air flow meter

  • EDU (P0200 set simultaneously)

  • Vehicle modifications

  • Low quality fuel

  • Frozen fuel

  • ECM

Tech Tips


  • Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors causing the malfunction.

  • Check that the vehicle has not been modified in any way prior to the vehicle inspection.

  • This troubleshooting procedure checks for the cause of an obvious lack of engine power (the vehicle speed does not reach the target speed in the high speed range) while the vehicle is being driven.

INSPECTION PROCEDURE

Note


  • After replacing the ECM, the new ECM needs registration Click here and initialization Click here.

  • After replacing the fuel injector, the ECM needs registration Click here

  • If the supply pump assembly is replaced, the ECM needs initialization Click here

Tech Tips

Before troubleshooting, conduct the following:


  • (a)Check the fuel quality.


  • (b)Check the fuel for air.


  • (c)Check the fuel system for blockages.


  • (d)Check the air filter.


  • (e)Check the engine oil.


  • (f)Check the engine coolant.


  • (g)Check the engine idling speed and the maximum engine speed.


  • (h)Check the vacuum pump assembly.

PROCEDURE


  1. READ OUTPUT DTC (RELATING TO ENGINE)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Enter the following menus: Powertrain / Engine and ECT / DTC.

    4. Read pending DTCs.

      Result
      Result Proceed to
      No DTCs are output A
      Engine related DTCs are output B

    B
    A
  2. TAKE SNAPSHOT DURING IDLING AND 4000 rpm


    1. A01KG3HE39
      Text in Illustration
      *1 Snapshot Button

      Connect the intelligent tester to the DLC3.

    2. Start the engine and warm it up, and A/C switch and all accessory switches should off.

    3. Turn the tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.

    5. With no load after the engine is warmed up, take a snapshot when idling and at 4000 rpm.

      Tech Tips


      • A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.

      • Graphs can be displayed by transferring the stored snapshot data from the tester to a PC. Intelligent Viewer must be installed on the PC.


    NEXT
  3. TAKE SNAPSHOT DURING LACK OF POWER


    1. A01KG3HE39
      Text in Illustration
      *1 Snapshot Button

      Connect the intelligent tester to the DLC3.

    2. Start the engine and turn the tester on.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.

    4. Take a snapshot of the following Data List items with the intelligent tester during lack of power.

      Tech Tips


      • A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.

      • Graphs can be displayed by transferring the stored snapshot data from the tester to a PC. Intelligent Viewer must be installed on the PC.

      • Move the shift lever to 2nd gear and accelerate the vehicle with the accelerator fully open (obey all laws and regulations, and pay attention to driving conditions while driving the vehicle). Then, check the Data List with the engine warmed up and idling (the shift lever in neutral and A/C switch and all accessory switches off).


    NEXT
  4. CHECK SNAPSHOT (MAP AND MAF)


    1. Check MAP and MAF in the snapshot taken when the engine was running at 4000 rpm with no load.

      Result
      Result Proceed to
      MAP is 110 kPa or more and MAF is 100 g/sec. or more A
      MAP is less than 90 kPa B
      Except above C

    B
    C
    A
  5. CHECK SNAPSHOT (MAP, TARGET BOOSTER PRESSURE, FUEL PRESS AND TARGET COMMON RAIL PRESSURE)


    1. Check MAP, Target Booster Pressure, Fuel Press and Target Common Rail Pressure in the snapshot taken when the vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.

      Result
      Result Proceed to
      Difference between MAP and Target Booster Pressure is +/-20 kPa or more A
      Difference between Fuel Press and Target Common Rail Pressure is +/-20000 kPa or more B
      Except above C

    B
    C
    A
  6. CHECK INTAKE SYSTEM


    1. Check for air leakage and blockage between the air cleaner and turbocharger, and between the turbocharger and intake manifold.

      Tech Tips


      • Check that the intercooler is not clogged with foreign matter.

      • Check that there are no disconnected, pinched or leaking hoses or pipes.

      • Check that there are no modifications made by the user.

      OK
      No leakage or blockage.

    NG
    OK
  7. INSPECT TURBOCHARGER SUB-ASSEMBLY


    1. Inspect the turbocharger sub-assembly Click here


    NG
    OK
  8. CLEAN OR REPLACE FUEL FILTER


    1. Clean or replace the fuel filter.

      Tech Tips

      Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.


    NEXT
  9. REPLACE FUEL INJECTORS OF ALL CYLINDERS


    1. Replace the fuel injectors Click here.


    NEXT
  10. BLEED AIR FROM FUEL SYSTEM


    1. Bleed the air from the fuel system Click here.


    NEXT
  11. REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING


    1. Register the injector compensation code Click here.

    2. Perform the fuel injector pilot quantity learning Click here.


    NEXT
  12. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    NEXT
  13. READ VALUE USING INTELLIGENT TESTER (MAP AND ATMOSPHERIC PRESSURE)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.

    4. Compare MAP to Atmosphere Pressure when the ignition switch is ON (do not start the engine).

      Standard
      Difference between MAP and Atmosphere Pressure is less than 8 kPa.

      Tech Tips


      • If MAP and Atmosphere Pressure have the same value, both are normal. If there is a difference of 8 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.

      • Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. This varies by weather.

      Result
      Result Proceed to
      MAP and Atmosphere Pressure have the same value A
      MAP is different from actual atmospheric pressure B
      Atmosphere Pressure is different from actual atmospheric pressure C

    B
    C
    A
  14. CHECK AIR INTAKE SYSTEM


    1. Check for air leaks and blockages between the air cleaner case and turbocharger, and between the turbocharger and intake manifold.

      Result
      Result Proceed to
      Leaks and/or blockages exist in the intake system A
      No leaks or blockages in the intake system B

      Tech Tips


      • Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.

      • Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.

      • Using your hand, check whether the pipes and hoses in the intake system are securely connected.

      • By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.

      • Check for any modifications in the intake system made by the user.


    B
    A
  15. REPAIR OR REPLACE AIR INTAKE SYSTEM


    1. Repair or replace the malfunctioning part in the air intake system.


    NEXT
  16. REPLACE TURBOCHARGER SUB-ASSEMBLY


    1. Replace the turbocharger sub-assembly Click here.


    NEXT
  17. REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR


    1. Replace the manifold absolute pressure sensor.


    NEXT
  18. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT
  19. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    NEXT
  20. BLEED AIR FROM FUEL SYSTEM


    1. Bleed the air from the fuel system Click here.


    NEXT
  21. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure.

    4. A01KG3HE39
      Text in Illustration
      *1 Snapshot Button

      Take a snapshot with the intelligent tester during the Active Test.

      Tech Tips

      Detailed graphs can be displayed by transferring the stored snapshot from the tester to a PC (personal computer) with Intelligent Viewer installed.

    5. Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.

      Tech Tips

      In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.

      A01KH3ME05
      OK
      The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10,000 kPa.

      Tech Tips


      • "Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.

      • "Fuel Press" is the actual fuel pressure.


    NG
    OK
  22. CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP


    1. Disconnect the inlet hose from the fuel supply pump.

    2. Operate the priming pump and check that fuel is being supplied to the fuel supply pump.

      OK
      Fuel is properly supplied to the fuel supply pump when the priming pump is operated.

      Tech Tips


      • When there is a lack of fuel, the fuel pressure drops.

      • Inspect for fuel filter clogging.

        (Check that the fuel filter is not clogged.)


    NG
    OK
  23. REPLACE SUCTION CONTROL VALVE


    1. Replace the suction control valve Click here.


    NEXT
  24. REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP)


    1. Check and repair or replace the clogged fuel pipe.


    NEXT
  25. BLEED AIR FROM FUEL SYSTEM


    1. Bleed the air from the fuel system Click here.


    NEXT
  26. PERFORM FUEL SUPPLY PUMP INITIALIZATION


    1. Perform fuel supply pump initialization Click here.


    NEXT
  27. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure.

    4. A01KG3HE39
      Text in Illustration
      *1 Snapshot Button

      Take a snapshot with the intelligent tester during the Active Test.

      Tech Tips

      Detailed graphs can be displayed by transferring the stored snapshot from the tester to a PC (personal computer) with Intelligent Viewer installed.

    5. Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.

      Tech Tips

      In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.

      A01KH3ME05
      OK
      The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10,000 kPa.

      Tech Tips


      • "Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.

      • "Fuel Press" is the actual fuel pressure.


    NEXT
  28. CHECK AIR INTAKE SYSTEM


    1. Check for air leaks and blockages between the air cleaner case and turbocharger, and between the turbocharger and intake manifold.

      Result
      Result Proceed to
      No leaks or blockages in the intake system A
      Leaks and/or blockages exist in the intake system B

      Tech Tips


      • Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.

      • Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.

      • Using your hand, check whether the pipes and hoses in the intake system are securely connected.

      • By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.

      • Confirm that the connecting hose between the manifold absolute pressure sensor and the intake manifold has not moved out of position.

      • Check for any modifications in the intake system made by the user.


    B
    A
  29. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EGR CUT)


    1. Connect the intelligent tester to the DLC3.

    2. Start the engine and warm it up, and the A/C switch and all accessory switches should be off.

    3. Turn the tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EGR Cut.

    5. Check the MAF during the Active Test.

      Result
      Result Proceed to
      When EGR is cut, MAF value is less than 15 g/sec. A
      Except above B
      Reference
      EGR Valve Condition (Opening) Measuring Condition MAF (Reference)
      Open (55%)
      • Atmosphere pressure: 101 kPa

      • Intake air temperature: 30°C (86°F)

      • Engine coolant temperature: 88°C (190°F)

      3.0 to 9.0 g/sec.
      Close (0%) 15 to 22 g/sec.

    B
    A
  30. READ VALUE USING INTELLIGENT TESTER (MAF)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

    4. Read the value.

      Standard
      Tester Display Condition Specified Condition
      MAF Engine not running Below 0.3 g/sec

    NG
    OK
  31. CHECK FOR DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)


    1. Remove the electric EGR control valve assembly.

    2. Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the EGR valve assembly.

      Tech Tips


      • If the EGR valve is stuck closed, the intake air amount increases and engine vibration may worsen.

      • If the EGR valve does not operate due to clogging or disconnection of the vacuum hose, repair the hose.

      • If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power.

      • If there is an extremely large amount of deposit in the EGR valve, the EGR valve should be replaced.


    NEXT
  32. REPAIR OR REPLACE AIR INTAKE SYSTEM


    1. Repair or replace the malfunctioning part in the air intake system.


    NEXT
  33. REPLACE MASS AIR FLOW METER


    1. Replace the mass air flow meter Click here.

      Tech Tips

      Before replacing the mass air flow meter, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.


    NEXT
  34. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    NEXT
  35. READ VALUE USING INTELLIGENT TESTER (MAF)


    1. Connect the intelligent tester to the DLC3.

    2. Start the engine and turn the tester on.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

    4. Take a snapshot when the engine speed is maintained at 4000 rpm with no load.

    5. Read the values of "MAF" in the Data List using the snapshot review function.

      Standard
      MAF is 100 g/sec. or more

    NG
    OK
  36. CHECK EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY


    1. Remove the exhaust manifold converter sub-assembly.

    2. Visually check for catalyst clogging or carbon deposits adhering to the inner wall of the exhaust pipe upstream of the catalyst.

      OK
      Less than 10% of the cells are clogged.

    OK
    NG
  37. REPLACE MASS AIR FLOW METER


    1. Replace the mass air flow meter Click here.

      Tech Tips

      Before replacing the mass air flow meter, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.


    NEXT
  38. REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY


    1. Replace the exhaust manifold converter sub-assembly.


    NEXT
  39. CHECK FOR INTERMITTENT PROBLEMS


    1. Check for intermittent problems Click here.


    NEXT
  40. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    NEXT