PROPELLER SHAFT ASSEMBLY INSPECTION

Note


  • When using a vise, place aluminum plates between the part and vise.

  • When using a vise, do not overtighten it.


  1. INSPECT PROPELLER SHAFT ASSEMBLY


    1. Check the shaft tube for wear or damage.

    2. A01CH8X

      Set the propeller shaft assembly on V blocks. Using a dial indicator, measure the runout of the center of the propeller shaft assembly.

      Standard runout
      0 to 0.6 mm (0 to 0.0236 in.)
      Maximum runout
      1.0 mm (0.0394 in.)

      If the shaft runout is more than the maximum, replace the propeller shaft assembly.

  2. INSPECT CENTER PROPELLER SHAFT ASSEMBLY (for 4 Joint Type)


    1. Check the shaft tube for wear or damage.

    2. A01CHFX

      Set the center propeller shaft assembly on V blocks. Using a dial indicator, measure the runout of the center of the center propeller shaft assembly.

      Standard runout
      0 to 0.6 mm (0 to 0.0236 in.)
      Maximum runout
      1.0 mm (0.0394 in.)

      If the shaft runout is more than the maximum, replace the center propeller shaft assembly.

  3. INSPECT PROPELLER INTERMEDIATE SHAFT ASSEMBLY


    1. Check the shaft tube for wear or damage.

    2. A01CHFX

      Set the propeller intermediate shaft assembly on V blocks. Using a dial indicator, measure the runout of the center of the propeller intermediate shaft assembly.

      Standard runout
      0 to 0.6 mm (0 to 0.0236 in.)
      Maximum runout
      1.0 mm (0.0394 in.)

      If the shaft runout is more than the maximum, replace the propeller intermediate shaft assembly.

  4. INSPECT UNIVERSAL JOINT SPIDER ASSEMBLY


    1. Check the universal joint spider assembly and spider bearing for wear or damage.

    2. A01CJCW

      Shake the universal joint spider assembly in the axial and right angle directions strongly with both hands, and check that there is no looseness in the universal joint spider assembly and spider bearing.

      If there is deformation or damage, replace the universal joint spider assembly or spider bearing.

  5. INSPECT SPIDER BEARING


    1. A01CI7UE01
      Text in Illustration
      *1 Universal joint spider assembly
      *2 Spider bearing

      Check the universal joint spider assembly and spider bearing for wear or damage.

      If there are any scratches or cracks in the spider journal area or on the spider bearing, replace the universal joint spider assembly or spider bearing.

    2. Measure the clearance of the spider bearing.


      1. A01CGW4E02

        Using a caliper gauge, measure the bore diameter A of the bearing case of the spider bearing.

      2. A01CHERE02

        Using a micrometer, measure diameter B of the needle roller.

      3. A01CH7YE02

        Using a micrometer, measure diameter C of the journal of the universal joint spider assembly.

    3. A01CGO7E02

      Calculate the clearance between the spider journal and spider bearing as follows: Subtract twice the outside diameter (B x 2) of the needle roller from inside diameter A of the bearing case, and then subtract the result from outside diameter C of the spider journal.

      Standard clearance
      0.022 to 0.061 mm (0.0009 to 0.0024 in.)
      Maximum clearance
      0.1 mm (0.0039 in.)

      If the clearance is more than the maximum, replace the universal joint spider assembly and spider bearing.

  6. INSPECT CENTER NO. 1 SUPPORT BEARING ASSEMBLY


    1. A01CGTL

      Check that the center No. 1 support bearing assembly rotates smoothly when rotated by hand and check that there are no cracks or damage.

      Note

      Do not soak the center bearing in the cleaner.

      If there are any malfunctions, replace the center No. 1 support bearing assembly.

      If there is any damage to the lip of the center bearing case, replace the center No. 1 support bearing assembly.

    2. A01CGY5E01
      Text in Illustration
      *1 Center No. 1 support bearing cushion sub-assembly
      *2 Center No. 1 support bearing plate

      Check the center No. 1 support bearing cushion sub-assembly and center No. 1 support bearing plate for wear or damage.

      If there are any scratches or cracks on the surface of the center No. 1 support bearing cushion sub-assembly or damage on the center No. 1 support bearing plate, replace them.

  7. INSPECT UNIVERSAL JOINT SLEEVE YOKE SUB-ASSEMBLY


    1. A01CJ9BE02
      A01CHJ1

      Fixing the sliding yoke horizontally in a vise, place a dial indicator onto the yoke of the universal joint sleeve yoke to measure the free play.

      Text in Illustration
      *a 50 mm (1.97 in.)

      Tech Tips

      Place the dial indicator at a spot 50 mm (1.97 in.) away from the center of the universal joint sleeve yoke.

      Standard free play
      0.185 to 0.393 mm (0.0073 to 0.0154 in.)
      Maximum free play
      0.63 mm (0.0248 in.)

      If the free play is more than the maximum, replace the propeller shaft assembly.