EXHAUST PIPE INSTALLATION


  1. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    1. A01CI20E01

      Install a new gasket and front exhaust pipe assembly, and temporarily tighten 3 new nuts.

    2. A01CHG1

      Temporarily tighten the bolt.

    3. Tighten the 3 nuts.

      Torque:
      70 N*m  { 714 kgf*cm, 52 ft.*lbf }
    4. Tighten the bolt.

      Torque:
      25 N*m  { 250 kgf*cm, 18 ft.*lbf }
  2. INSTALL CENTER EXHAUST PIPE ASSEMBLY


    1. A01CI0EE01

      Install the center exhaust pipe assembly with 3 new nuts and 3 cushions.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }
    2. A01CHWFE01

      Connect the 2 differential pressure sensor hoses.

  3. INSTALL EXHAUST GAS TEMPERATURE SENSOR


    1. A01CI3ZE01

      Using a union nut wrench (14 mm), install the exhaust gas temperature sensor onto the center exhaust pipe assembly.

      Torque:
      without union nut wrench
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }
      with union nut wrench
      27 N*m  { 275 kgf*cm, 20 ft.*lbf }

      Tech Tips


      • Refer to the torque above when not using a union nut wrench. When not using a union nut wrench, calculate the torque in accordance with the lengths of union nut wrench and the torque wrench Click here.

      • Do not damage the exhaust gas temperature sensor.

    2. Connect the exhaust gas temperature sensor connector.

  4. INSTALL NO. 2 EXHAUST GAS TEMPERATURE SENSOR


    1. A01CIG0E01

      Using a union nut wrench (14 mm), install the No. 2 exhaust gas temperature sensor onto the center exhaust pipe assembly.

      Torque:
      without union nut wrench
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }
      with union nut wrench
      27 N*m  { 275 kgf*cm, 20 ft.*lbf }

      Tech Tips


      • Refer to the torque above when not using a union nut wrench. When not using a union nut wrench, calculate the torque in accordance with the lengths of union nut wrench and the torque wrench Click here.

      • Do not damage the exhaust gas temperature sensor.

    2. Connect the No. 2 exhaust gas temperature sensor connector and clamp.

  5. INSTALL EXHAUST RETARDER ASSEMBLY


    1. A01CHNOE01

      Install 2 new gaskets and exhaust retarder assembly with the 4 bolts.

      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }
    2. A01CIBFE01

      Connect the vacuum hose.

  6. INSTALL TAIL EXHAUST PIPE ASSEMBLY (for Front)


    1. A01CHH6E01

      Install the tail exhaust pipe assembly with 2 new nuts and the No. 1 exhaust pipe support.

      Torque:
      24 N*m  { 245 kgf*cm, 17 ft.*lbf }
  7. INSTALL TAIL EXHAUST PIPE ASSEMBLY (for Rear)


    1. Install the tail exhaust pipe assembly with 2 new nuts and the No. 1 exhaust pipe support.

      Torque:
      24 N*m  { 245 kgf*cm, 17 ft.*lbf }
  8. INSPECT FOR EXHAUST GAS LEAK

  9. INSPECT FOR CENTER EXHAUST PIPE ASSEMBLY


    1. A01CI4ZE13

      Check if the exhaust center pipe assembly bellows pipe is installed as shown in the illustration.