FUEL FILTER (for Engine Room Side) INSTALLATION


  1. INSTALL DIESEL FUEL FILTER ASSEMBLY


    1. Check and clean the diesel fuel filter installation surface.

    2. Apply clean fuel to the O-ring of a new diesel fuel filter assembly.

    3. Tighten the filter by hand until the O-ring contacts the installation surface.

    4. A01CI5XE01

      Using SST, tighten the fuel filter an additional 2/3 of a turn after the O-ring contacts the installation surface.

      SST
      09228-78010
  2. INSTALL NO. 3 NOZZLE LEAKAGE PIPE SUB-ASSEMBLY


    1. Install the No. 3 nozzle leakage pipe sub-assembly and 2 new gaskets with the 2 union bolts.

      Torque:
      20 N*m  { 200 kgf*cm, 14 ft.*lbf }
    2. Install the fuel pipe clamp with the nut.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
  3. CONNECT FUEL RETURN PIPE SUB-ASSEMBLY


    1. Install a new gasket to the fuel return pipe sub-assembly.

    2. Connect the fuel return pipe sub-assembly with the union bolt.

      Torque:
      20 N*m  { 200 kgf*cm, 14 ft.*lbf }
    3. Install the fuel pipe clamp with the nut.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
  4. INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY


    1. A01CHNRE02

      Install the No. 4 fuel pipe sub-assembly and 4 new gaskets with the 2 union bolts.

      Torque:
      for union bolt A
      25 N*m  { 250 kgf*cm, 18 ft.*lbf }
      for union bolt B
      20 N*m  { 200 kgf*cm, 14 ft.*lbf }
  5. BLEED AIR FROM FUEL SYSTEM


    1. A01CHFE

      Loosen the bleeder plug.

      Text in Illustration
      A01CHW8 Bleeder Plug

      Note

      Make sure that the drain plug and bleeder plug of the filter on the fuel tank side are closed.

    2. A01CHX4

      Bleed air using the priming pump on the fuel tank side.

      Note


      • Place a container, etc. underneath the fuel filter to prevent fuel from spraying.

      • The hand pump must be pushed with a full stroke during pumping.

      • The maximum hand pump pumping speed is 2 strokes per second.

      • When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.

      • If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.

      • If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.

      • If air bleeding using the hand pump is incomplete, the common rail pressure does not rise to the pressure range necessary for normal use and the engine cannot be started.

    3. Tighten the bleeder plug.

      Torque:
      6.9 N*m  { 70 kgf*cm, 61 in.*lbf }
    4. Check if the engine starts.

      Note


      • Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.

      • Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.

      • Use a fully-charged battery.


      1. When the engine can be started, proceed to the next step.

        Tech Tips

        If the engine cannot be started, bleed air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.

    5. Turn the ignition switch off.

    6. Connect the intelligent tester to the DLC3.

    7. Turn the ignition switch to ON and turn the intelligent tester on.

    8. Clear the DTCs Click here.

    9. Start the engine.*1

    10. A01CJCTE05
      Text in Illustration
      *a

      Reference

      (Active Test operation)

      Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2

    11. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3

      A01CHBIE15
      Text in Illustration
      *a Active Test operation *b Time
      *c ON *d OFF
      *e 1st time *f 2nd time
      *g 5th time *h 10 seconds
      *i 3 minutes or more - -
    12. Allow the engine to idle for 3 minutes or more after performing the Active Test for the 5th time.

    13. Enter the following menus: Powertrain / Engine and ECT / DTC.

    14. Read Current DTCs.


      1. If no DTCs are output, air bleeding is completed.

      2. If DTCs are output, perform the following procedure.

    15. Clear the DTCs Click here.

    16. Repeat steps *1 to *3.

    17. Enter the following menus: Powertrain / Engine and ECT / DTC.

    18. Read Current DTCs.

      OK
      No DTCs are output
  6. INSPECT FOR FUEL LEAK


    1. Perform the Active Test.


      1. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

        Note

        Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

      2. Connect the intelligent tester to the DLC3.

      3. Start the engine.

      4. Turn the intelligent tester on.

      5. Enter the following menus: Powertrain / Engine and ECT / Active Test.

      6. Perform the Active Test.

        Tester Display Test Part Control Range Diagnostic Note
        Test the Fuel Leak Pressurizes common rail interior and checks for fuel leaks Stop or Start
        • The fuel pressure inside the common rail is increased to a specified value and the engine speed is increased to 2000 rpm when Start is selected

        • The above conditions are preserved while the control parameter of the test is Start

    2. Check for leaks from the fuel system while performing the Active Test (with a fuel pressure applied).