Note
Do not allow dirt and water to enter parts.
Make sure that there is no dirt at the connections before installing parts.
Air enters the fuel pipe when installing the fuel filter case. Thoroughly purge air from the fuel pipe after installation.
INSTALL COMMON RAIL ASSEMBLY
Install the common rail assembly fuel pipe support and common rail assembly with the 2 bolts.
Note
Make sure that no foreign matter or water enters the parts during the procedure.
Make sure that there is no foreign matter at the connections between parts.
Install a new gasket to the fuel pipe.
Note
Make sure that no foreign matter or water enters the parts during the procedure.
Make sure that there is no foreign matter at the connections between parts.
Install the fuel pipe with the union bolt.
Note
Make sure that no foreign matter or water enters the parts during the procedure.
Make sure that there is no foreign matter at the connections between parts.
Connect the fuel pressure sensor connector.
Push on the connector until the spring lock makes a noise and returns to its original position.
Tech Tips
It is not necessary to push the spring lock down when connecting the connector.
INSTALL INJECTION PIPE SUB-ASSEMBLY
Temporarily install the injection pipe sub-assembly with the 8 union nuts.
Note
If the common rail has been replaced, the injection pipes must also be replaced.
Using a 17 mm union nut wrench, tighten the 8 union nuts.
Note
Refer to the torque above when not using the union nut wrench. When using the union nut wrench, calculate the torque in accordance with the lengths of the union nut wrench and torque wrench Click here.
CONNECT FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY
Temporarily install the fuel filter to injection pump fuel pipe sub-assembly.
Note
Make sure that no foreign matter or water enters the parts during the procedure.
Make sure that there is no foreign matter at the connections between parts.
Tech Tips
Tighten the nuts until they cannot be turned any further.
Using a 17 mm union nut wrench, install the fuel filter to injection pump fuel pipe with the union nut.
Note
Refer to the torque above when not using the union nut wrench. When using the union nut wrench, calculate the torque in accordance with the lengths of the union nut wrench and torque wrench Click here.
Install the 2 fuel pipe clamps with the 2 nuts.
INSTALL FUEL SUPPORT
Temporarily install the fuel support with the 2 bolts.
Install the 2 injection pipe clamps with the 2 bolts.
Tighten the 2 bolts of the fuel support.
INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
Apply a small amount of clean engine oil to a new O-ring.
Install the O-ring to the engine oil level dipstick guide.
Install the engine oil level dipstick guide with the bolt.
Install the engine oil level dipstick.
INSTALL HARNESS BRACKET
Install the harness bracket with the bolt.
Connect each wire harness and clamp.
INSTALL EGR COOLER SUB-ASSEMBLY
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
BLEED AIR FROM FUEL SYSTEM
Loosen the bleeder plug.
|
Bleeder Plug |
Note
Make sure that the drain plug and bleeder plug of the filter on the fuel tank side are closed.
Bleed air using the priming pump on the fuel tank side.
Note
Place a container, etc. underneath the fuel filter to prevent fuel from spraying.
The hand pump must be pushed with a full stroke during pumping.
The maximum hand pump pumping speed is 2 strokes per second.
When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
If air bleeding using the hand pump is incomplete, the common rail pressure does not rise to the pressure range necessary for normal use and the engine cannot be started.
Tighten the bleeder plug.
Check if the engine starts.
Note
Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.
Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
Use a fully-charged battery.
When the engine can be started, proceed to the next step.
Tech Tips
If the engine cannot be started, bleed air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs Click here.
Start the engine.*1
| *a | Reference (Active Test operation) |
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
| *a | Active Test operation | *b | Time |
| *c | ON | *d | OFF |
| *e | 1st time | *f | 2nd time |
| *g | 5th time | *h | 10 seconds |
| *i | 3 minutes or more | - | - |
Allow the engine to idle for 3 minutes or more after performing the Active Test for the 5th time.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
If no DTCs are output, air bleeding is completed.
If DTCs are output, perform the following procedure.
Clear the DTCs Click here.
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
| OK |
|---|
| No DTCs are output |
INSPECT FOR FUEL LEAK
Perform the Active Test.
Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.
Note
Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Test the Fuel Leak | Pressurizes common rail interior and checks for fuel leaks | Stop or Start |
|
Check for leaks from the fuel system while performing the Active Test (with a fuel pressure applied).
INSPECT FOR COOLANT LEAK
CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
Note
Before each inspection, turn the A/C switch off.
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 137 kPa (1.4 kgf/cm2, 20 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator assembly and engine water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.