FUEL SUPPLY PUMP INSTALLATION

Note


  • Do not allow dirt and water to enter parts.

  • Make sure that there is no dirt at the connections before installing parts.

  • Air enters the fuel pipe when installing the fuel filter case. Thoroughly purge air from the fuel pipe after installation.


  1. INSTALL INJECTION PUMP DRIVE GEAR


    1. Install a new O-ring to the timer cover.

    2. Install the timer cover to the supply pump assembly with the 2 bolts.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
    3. Temporarily install the crankshaft angle sensor plate and injection pump drive gear with the nut.

    4. Mount the injection pump drive gear in a vise between aluminum plates.

      Note

      Do not damage the gears.

    5. Tighten the nut.

      Torque:
      64 N*m  { 650 kgf*cm, 47 ft.*lbf }
  2. INSTALL SUPPLY PUMP ASSEMBLY


    1. Install a new O-ring to the timer cover.

    2. A01CH8BE05
      Text in Illustration
      *1 Matchmark
      *2 Hole

      Turn the injection pump drive gear and align the hole with the matchmark as shown in the illustration.

    3. A01CHDOE02
      Text in Illustration
      *1 Matchmark

      Align the matchmarks of the timer cover and front end plate, and then install the supply pump assembly with the 4 bolts.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }

      Note


      • Make sure the crankshaft is at the No. 1 cylinder top dead center position.

      • Make sure that no foreign matter or water enters the parts during the procedure.

      • Make sure that there is no foreign matter at the connections between parts.

    4. A01CHOV

      When the crankshaft position sensor installation hole can be accessed directly:


      1. Check that the knock pin of the injection pump drive gear is at the center of the hole.

    5. A01CIIVE01
      Text in Illustration
      *1 Vinyl Tape
      *a 36 mm (1.42 in.)

      When the crankshaft position sensor installation hole cannot be accessed directly:


      1. Tape the screwdriver as shown in the illustration.

      2. A01CHI0E01
        Text in Illustration
        *1 Service Plug

        Remove the service plug and gasket from the timing gear case.

      3. A01CHN5E01
        Text in Illustration
        *1 Timing Gear Case
        *2 Injection Pump Drive Gear
        *3 Screwdriver
        *a 0 to 2 mm of the tape is visible
        *b 10 mm or more of the tape is visible

        Insert the taped screwdriver it into the timing gear case. Check that the tape and end of the timing gear case are aligned.

      4. Install the service plug and a new gasket to the timing gear case.

        Torque:
        8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
    6. Install the injection pump stay with the 2 bolts and nut.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
    7. Connect the suction control valve connector and fuel temperature sensor connector.

    8. Install the wire harness clamp bracket to the injection pump stay with the bolt.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
    9. Attach the wire harness clamp to the wire harness clamp bracket.

  3. INSTALL CRANKSHAFT POSITION SENSOR


    1. Apply a light coat of engine oil to the O-ring of the crankshaft position sensor.

      Note

      When reusing the crankshaft position sensor, inspect the O-ring.

    2. Install the crankshaft position sensor with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Make sure that the O-ring is not cracked and does not come out of position during installation.

    3. Connect the crankshaft position sensor connector.

  4. INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY


    1. Temporarily install a new fuel filter to injection pump fuel pipe sub-assembly to the supply pump assembly and common rail assembly.

      Note


      • Make sure that no foreign matter or water enters the parts during the procedure.

      • Make sure that there is no foreign matter at the connections between parts.

      • Always replace the fuel filter to injection pump fuel pipe sub-assembly with a new one as the pipe is subject to high pressure and may leak when reused.

      Tech Tips

      Tighten the nuts until they cannot be turned any further.

    2. Using a 17 mm union nut wrench, install the fuel filter to injection pump fuel pipe with the 2 union nuts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

      Note

      Refer to the torque above when not using the union nut wrench. When using the union nut wrench, calculate the torque in accordance with the lengths of the union nut wrench and torque wrench Click here.

    3. Install the 2 fuel pipe clamps with the 2 nuts.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
  5. INSTALL FUEL PIPE SUB-ASSEMBLY


    1. Install the gasket and fuel return pipe sub-assembly with the union bolt.

      Torque:
      20 N*m  { 200 kgf*cm, 14 ft.*lbf }
    2. Connect the fuel hose to the fuel return pipe sub-assembly, and slide the clip to secure the hose.

    3. Connect the No. 1 fuel pipe to the supply pump assembly, and slide the clip to secure the hose.

    4. Install the 4 gaskets and No. 3 fuel pipe with the 2 union bolts.

      Torque:
      25 N*m  { 250 kgf*cm, 18 ft.*lbf }
    5. Install the 3 gaskets and No. 2 fuel pipe with the 2 union bolts.

      Torque:
      25 N*m  { 250 kgf*cm, 18 ft.*lbf }
    6. Install the 4 fuel pipe clamps with the 4 nuts.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
  6. INSTALL WIRE HARNESS CLAMP BRACKET


    1. Install the wire harness clamp bracket with the bolt.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
    2. Install the power steering suction support union with the bolt.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
    3. Attach the 2 wire harness clamps.

  7. INSTALL NO. 1 INTAKE PIPE

    Click here

  8. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE


    1. Apply a small amount of clean engine oil to a new O-ring.

    2. Install the O-ring to the engine oil level dipstick guide.

    3. Install the engine oil level dipstick guide with the bolt.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
    4. Install the engine oil level dipstick.

  9. INSTALL HARNESS BRACKET


    1. Install the harness bracket with the bolt.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
    2. Connect each wire harness and clamp.

  10. INSTALL NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY


    1. Install 4 new No. 2 cylinder head cover gaskets to the 4 injector assemblies.

    2. Install a new cylinder head cover gasket and the No. 2 cylinder head cover sub-assembly.

    3. Install the 2 cylinder head cover cushions and 2 spacers to the No. 2 cylinder head cover sub-assembly with the 2 bolts.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
    4. Install the cylinder head cover cushion rubber to the No. 2 cylinder head cover sub-assembly.

    5. Connect the 4 connectors and install the wire harness with the bolt.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
  11. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


    1. Install the 2 cylinder head cover stays and cylinder head cover sub-assembly with the 2 bolts.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
  12. INSTALL EGR COOLER SUB-ASSEMBLY

    Click here

  13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  14. BLEED AIR FROM FUEL SYSTEM


    1. A01CHFE

      Loosen the bleeder plug.

      Text in Illustration
      A01CHW8 Bleeder Plug

      Note

      Make sure that the drain plug and bleeder plug of the filter on the fuel tank side are closed.

    2. A01CHX4

      Bleed air using the priming pump on the fuel tank side.

      Note


      • Place a container, etc. underneath the fuel filter to prevent fuel from spraying.

      • The hand pump must be pushed with a full stroke during pumping.

      • The maximum hand pump pumping speed is 2 strokes per second.

      • When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.

      • If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.

      • If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.

      • If air bleeding using the hand pump is incomplete, the common rail pressure does not rise to the pressure range necessary for normal use and the engine cannot be started.

    3. Tighten the bleeder plug.

      Torque:
      6.9 N*m  { 70 kgf*cm, 61 in.*lbf }
    4. Check if the engine starts.

      Note


      • Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.

      • Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.

      • Use a fully-charged battery.


      1. When the engine can be started, proceed to the next step.

        Tech Tips

        If the engine cannot be started, bleed air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.

    5. Turn the ignition switch off.

    6. Connect the intelligent tester to the DLC3.

    7. Turn the ignition switch to ON and turn the intelligent tester on.

    8. Clear the DTCs Click here.

    9. Start the engine.*1

    10. A01CJCTE05
      Text in Illustration
      *a

      Reference

      (Active Test operation)

      Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2

    11. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3

      A01CHBIE15
      Text in Illustration
      *a Active Test operation *b Time
      *c ON *d OFF
      *e 1st time *f 2nd time
      *g 5th time *h 10 seconds
      *i 3 minutes or more - -
    12. Allow the engine to idle for 3 minutes or more after performing the Active Test for the 5th time.

    13. Enter the following menus: Powertrain / Engine and ECT / DTC.

    14. Read Current DTCs.


      1. If no DTCs are output, air bleeding is completed.

      2. If DTCs are output, perform the following procedure.

    15. Clear the DTCs Click here.

    16. Repeat steps *1 to *3.

    17. Enter the following menus: Powertrain / Engine and ECT / DTC.

    18. Read Current DTCs.

      OK
      No DTCs are output
  15. INSPECT FOR FUEL LEAK


    1. Perform the Active Test.


      1. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

        Note

        Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

      2. Connect the intelligent tester to the DLC3.

      3. Start the engine.

      4. Turn the intelligent tester on.

      5. Enter the following menus: Powertrain / Engine and ECT / Active Test.

      6. Perform the Active Test.

        Tester Display Test Part Control Range Diagnostic Note
        Test the Fuel Leak Pressurizes common rail interior and checks for fuel leaks Stop or Start
        • The fuel pressure inside the common rail is increased to a specified value and the engine speed is increased to 2000 rpm when Start is selected

        • The above conditions are preserved while the control parameter of the test is Start

    2. Check for leaks from the fuel system while performing the Active Test (with a fuel pressure applied).

  16. INSPECT FOR OIL LEAK


    1. Start the engine. Make sure that there are no oil leaks from the areas that were worked on.

  17. PERFORM SUPPLY PUMP INITIALIZATION

    Click here