FUEL INJECTOR INSTALLATION

Note


  • Do not allow dirt and water to enter parts.

  • Make sure that there is no dirt at the connections before installing parts.

  • Air enters the fuel pipe when installing the fuel filter case. Thoroughly purge air from the fuel pipe after installation.


  1. INSTALL INJECTION NOZZLE SEAT GASKET


    1. Install 4 new injection nozzle seat gaskets to the cylinder head.

  2. INSTALL INJECTOR ASSEMBLY

    Note

    A01CJFWE04

    Register the injector compensation code of a new injector assembly in the ECM when replacing the injector assembly. Register the injector compensation code in advance so that it can be installed in the correct position Click here.


    1. Apply a small amount of clean engine oil to 4 new O-rings.

    2. Install an O-ring to each injector assembly.

    3. Install a new gasket to each injector assembly.

      Note


      • Apply engine oil to the O-ring. Be careful not to pinch the O-ring when installing it.

      • If the O-ring is damaged, fuel will leak and the engine cannot be started.

      • Do not install the injection pipe clamps until the injection pipe is temporarily installed.

    4. Referring to each cylinder number identification tag attached to the injector assemblies, install the correct injector assembly, nozzle holder clamp and nozzle holder clamp bolt for each cylinder.

      Note


      • When reusing the injector assemblies, reinstall them to the same cylinder they were removed from. Otherwise, it could cause the engine to malfunction.

      • Carefully insert the injector assemblies so that the O-ring is not caught between the cylinder head and the injector assembly.

      • Check that the tip of the injector assembly is free of foreign matter.

    5. Temporarily install the 4 nozzle holder clamps with the 4 nozzle holder clamp bolts.

      Note

      Be sure to install the nozzle holder clamps and bolts to their original positions.

    6. Install 4 new nozzle holder seals to the cylinder head.

      Note

      Securely insert the tip of each nozzle holder seal into each injector assembly.

    7. A01CIAR
      Text in Illustration
      *1 Injector Compensation Code

      Temporarily install the nozzle leakage pipe and 5 new gaskets with the 5 hollow screws.

      Note

      Make sure that the hollow screws and nozzle leakage pipe are not deformed or damaged.

    8. Temporarily install the union nuts of the 4 injection pipe sub-assemblies by hand.

      Note

      If an injector assembly has been replaced, the corresponding injection pipe sub-assembly must also be replaced.

    9. Tighten the 4 nozzle holder clamp bolts.

      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

      Note

      After tightening the nozzle holder clamp bolts, check that the injector assembly and the nozzle holder clamp do not interfere with the valve spring.

    10. Tighten the 5 hollow screws.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }

      Note

      If the nozzle leakage pipe assembly has been tightened to more than the specified torque, replace it with a new one.

  3. INSTALL INJECTION PIPE SUB-ASSEMBLY


    1. Temporarily install the injection pipe sub-assembly with the 8 union nuts.

      Note

      If the common rail has been replaced, the injection pipes must also be replaced.

    2. Using a 17 mm union nut wrench, tighten the 8 union nuts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

      Note

      Refer to the torque above when not using the union nut wrench. When using the union nut wrench, calculate the torque in accordance with the lengths of the union nut wrench and torque wrench Click here.

  4. INSTALL FUEL SUPPORT


    1. Temporarily install the fuel support with the 2 bolts.

    2. Install the 2 injection pipe clamps with the 2 bolts.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
    3. Tighten the 2 bolts of the fuel support.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
  5. INSTALL NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY


    1. Install 4 new No. 2 cylinder head cover gaskets to the 4 injector assemblies.

    2. Install a new cylinder head cover gasket and the No. 2 cylinder head cover sub-assembly.

    3. Install the 2 cylinder head cover cushions and 2 spacers to the No. 2 cylinder head cover sub-assembly with the 2 bolts.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
    4. Install the cylinder head cover cushion rubber to the No. 2 cylinder head cover sub-assembly.

    5. Connect the 4 connectors and install the wire harness with the bolt.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
  6. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


    1. Install the 2 cylinder head cover stays and cylinder head cover sub-assembly with the 2 bolts.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
  7. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE


    1. Apply a small amount of clean engine oil to a new O-ring.

    2. Install the O-ring to the engine oil level dipstick guide.

    3. Install the engine oil level dipstick guide with the bolt.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
    4. Install the engine oil level dipstick.

  8. INSTALL HARNESS BRACKET


    1. Install the harness bracket with the bolt.

      Torque:
      29 N*m  { 291 kgf*cm, 21 ft.*lbf }
    2. Connect each wire harness and clamp.

  9. INSTALL EGR COOLER SUB-ASSEMBLY

    Click here

  10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  11. REGISTER INJECTOR COMPENSATION CODE

    Click here

  12. INSPECT FOR INJECTOR COMPENSATION CODE

    Click here

  13. BLEED AIR FROM FUEL SYSTEM


    1. A01CHFE

      Loosen the bleeder plug.

      Text in Illustration
      A01CHW8 Bleeder Plug

      Note

      Make sure that the drain plug and bleeder plug of the filter on the fuel tank side are closed.

    2. A01CHX4

      Bleed air using the priming pump on the fuel tank side.

      Note


      • Place a container, etc. underneath the fuel filter to prevent fuel from spraying.

      • The hand pump must be pushed with a full stroke during pumping.

      • The maximum hand pump pumping speed is 2 strokes per second.

      • When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.

      • If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.

      • If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.

      • If air bleeding using the hand pump is incomplete, the common rail pressure does not rise to the pressure range necessary for normal use and the engine cannot be started.

    3. Tighten the bleeder plug.

      Torque:
      6.9 N*m  { 70 kgf*cm, 61 in.*lbf }
    4. Check if the engine starts.

      Note


      • Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.

      • Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.

      • Use a fully-charged battery.


      1. When the engine can be started, proceed to the next step.

        Tech Tips

        If the engine cannot be started, bleed air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.

    5. Turn the ignition switch off.

    6. Connect the intelligent tester to the DLC3.

    7. Turn the ignition switch to ON and turn the intelligent tester on.

    8. Clear the DTCs Click here.

    9. Start the engine.*1

    10. A01CJCTE05
      Text in Illustration
      *a

      Reference

      (Active Test operation)

      Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2

    11. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3

      A01CHBIE15
      Text in Illustration
      *a Active Test operation *b Time
      *c ON *d OFF
      *e 1st time *f 2nd time
      *g 5th time *h 10 seconds
      *i 3 minutes or more - -
    12. Allow the engine to idle for 3 minutes or more after performing the Active Test for the 5th time.

    13. Enter the following menus: Powertrain / Engine and ECT / DTC.

    14. Read Current DTCs.


      1. If no DTCs are output, air bleeding is completed.

      2. If DTCs are output, perform the following procedure.

    15. Clear the DTCs Click here.

    16. Repeat steps *1 to *3.

    17. Enter the following menus: Powertrain / Engine and ECT / DTC.

    18. Read Current DTCs.

      OK
      No DTCs are output
  14. INSPECT FOR FUEL LEAK


    1. Perform the Active Test.


      1. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

        Note

        Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

      2. Connect the intelligent tester to the DLC3.

      3. Start the engine.

      4. Turn the intelligent tester on.

      5. Enter the following menus: Powertrain / Engine and ECT / Active Test.

      6. Perform the Active Test.

        Tester Display Test Part Control Range Diagnostic Note
        Test the Fuel Leak Pressurizes common rail interior and checks for fuel leaks Stop or Start
        • The fuel pressure inside the common rail is increased to a specified value and the engine speed is increased to 2000 rpm when Start is selected

        • The above conditions are preserved while the control parameter of the test is Start

    2. Check for leaks from the fuel system while performing the Active Test (with a fuel pressure applied).

  15. INSPECT FOR COOLANT LEAK

    CAUTION:

    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

    Note

    Before each inspection, turn the A/C switch off.


    1. Fill the radiator with coolant and attach a radiator cap tester.

    2. Warm up the engine.

    3. Using the radiator cap tester, increase the pressure inside the radiator to 137 kPa (1.4 kgf/cm2, 20 psi), and check that the pressure does not drop.

      If the pressure drops, check the hoses, radiator assembly and engine water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.

  16. INSPECT FOR OIL LEAK


    1. Start the engine. Make sure that there are no oil leaks from the areas that were worked on.