ENGINE UNIT INSPECTION


  1. INSPECT VALVE ROCKER ARM OIL CLEARANCE


    1. A01CH75

      Using a caliper gauge, measure the inside diameter of the valve rocker arm bush.

      Standard bush inside diameter
      22.023 to 22.052 mm (0.8670 to 0.8681 in.)
      Maximum bush inside diameter
      22.08 mm (0.8693 in.)

      If the inside diameter is more than the maximum, replace the valve rocker arm bush.

      Note

      When installing a valve rocker arm bush into the valve rocker arm, align the valve rocker arm bush correctly with the 2 oil holes of the valve rocker arm.

    2. Using a micrometer, measure the outside diameter of the No. 1 valve rocker shaft sub-assembly.

      Standard shaft diameter
      21.959 to 21.980 mm (0.8645 to 0.8653 in.)
      Minimum shaft diameter
      21.92 mm (0.8630 in.)

      If the outside diameter is less than the minimum, replace the No. 1 valve rocker shaft sub-assembly.

    3. Subtract the No. 1 valve rocker shaft sub-assembly outside diameter measurement from the valve rocker arm inside diameter measurement

      Standard oil clearance
      0.043 to 0.093 mm (0.00169 to 0.00366 in.)
      Maximum oil clearance
      0.15 mm (0.00591 in.)

      If the oil clearance is more than the maximum, replace the No. 1 valve rocker shaft sub-assembly and valve rocker arm bush.

  2. INSPECT VALVE PUSH ROD


    1. Place the push rod on V-blocks.

    2. Using a dial indicator, measure the circle runout at the center of the valve push rod.

      Maximum circle runout
      0.30 mm (0.0118 in.)

      If the circle runout is more than the maximum, replace the valve push rod.

  3. INSPECT CYLINDER HEAD SET BOLT


    1. A01CGS1E05
      Text in Illustration
      *a Measurement Length

      Using a vernier caliper, measure the length of the cylinder head set bolt from the seat to the end.

      Standard length
      126 mm (4.96 in.)
      Maximum length
      129 mm (5.07 in.)

      If the length is more than the maximum, replace the cylinder head set bolt.

  4. INSPECT NO. 2 IDLE GEAR OIL CLEARANCE


    1. A01CI37

      Using a cylinder gauge, measure the inside diameter of the No. 2 idle gear sub-assembly.

      Standard inside diameter
      50.000 to 50.025 mm (1.9685 to 1.9695 in.)
      Maximum inside diameter
      50.05 mm (1.9704 in.)

      If the diameter is more than the maximum, replace the No. 2 idle gear sub-assembly.

    2. A01CJEY

      Using a micrometer, measure the diameter of the No. 2 idle gear shaft.

      Standard shaft diameter
      49.950 to 49.975 mm (1.9665 to 1.9675 in.)
      Minimum shaft diameter
      49.95 mm (1.9665 in.)

      If the diameter is less than the minimum, replace the No. 2 idle gear shaft.

    3. Subtract the No. 2 idle gear shaft diameter measurement from the No. 2 idle gear sub assembly inside diameter measurement.

      Standard oil clearance
      0.0125 to 0.0375 mm (0.000492 to 0.00148 in.)
      Maximum oil clearance
      0.10 mm (0.00394 in.)

      If the clearance is more than the maximum, replace the No. 2 idle gear sub-assembly and No. 2 idle gear shaft.

  5. INSPECT NO. 1 IDLE GEAR OIL CLEARANCE


    1. A01CHPI

      Using a cylinder gauge, measure the inside diameter of the No. 1 idle gear sub-assembly.

      Standard idle gear inside diameter
      50.000 to 50.025 mm (1.9685 to 1.9695 in.)
      Maximum idle gear inside diameter
      50.05 mm (1.9704 in.)

      If the diameter is more than the maximum, replace the No. 1 idle gear sub-assembly.

    2. A01CIS7

      Using a micrometer, measure the diameter of the No. 1 idle gear shaft.

      Standard idle gear shaft diameter
      49.950 to 49.975 mm (1.9665 to 1.9675 in.)
      Minimum idle gear shaft diameter
      49.95 mm (1.9665 in.)

      If the diameter is less than the minimum, replace the No. 1 idle gear shaft.

    3. Subtract the No. 1 idle gear shaft outside diameter measurement from the No. 1 idle gear sub assembly inside diameter measurement.

      Standard oil clearance
      0.0125 to 0.0370 mm (0.000492 to 0.00146 in.)
      Maximum oil clearance
      0.10 mm (0.00394 in.)

      If the clearance is more than the maximum, replace the No. 1 idle gear sub-assembly and No. 1 idle gear shaft.