FUEL FILTER REPLACEMENT

Tech Tips

If replacing only the fuel filter element sub-assembly, steps 2 through 5 are not necessary.


  1. REMOVE FUEL FILTER ELEMENT SUB-ASSEMBLY


    1. A01CHNKE01

      Disconnect the level warning switch connector.

    2. Place a drain pan under the filter.

    3. A01CGOR

      Loosen the drain plug and the air bleed plug as shown in the illustration. Drain the fuel.

      Note


      • Do not use any tools.

      • Do not allow any fuel to spill.

      • If any fuel spills on any part of the engine, wipe it clean with a shop rag or a piece of cloth.

    4. A01CHBS

      When fuel stops draining from the drain plug, tighten the drain plug and air bleed plug.

      Note

      Do not use any tools.

    5. A01CHGGE01

      Disengage the claw. Remove the cover by turning it counterclockwise approximately 120°.

    6. A01CHYJE01

      Remove the fuel filter element sub-assembly.

    7. Remove the O-ring from the fuel filter cover.

  2. REMOVE FUEL FILTER ASSEMBLY


    1. A01CHCL

      Disconnect the 2 fuel hoses.

    2. A01CHJQ

      Remove the 2 bolts and the fuel filter assembly.

  3. REMOVE FUEL SEDIMENT FILTER ASSEMBLY


    1. A01CJ95

      Loosen the drain plug as shown in the illustration. Drain the fuel.

      Note


      • Do not use any tools.

      • Do not allow any fuel to spill.

      • If any fuel spills on any part of the engine, wipe it clean with a shop rag or a piece of cloth.

    2. When fuel stops draining from the drain plug, tighten the drain plug.

    3. A01CH2G

      Disconnect the 2 fuel hoses.

    4. A01CHQT

      Remove the 2 bolts and the fuel sediment filter assembly.

  4. INSTALL FUEL SEDIMENT FILTER ASSEMBLY


    1. A01CHQT

      Install the fuel sediment filter assembly with the 2 bolts.

      Torque:
      44 N*m  { 449 kgf*cm, 33 ft.*lbf }
    2. A01CH2G

      Connect the 2 fuel hoses.

  5. INSTALL FUEL FILTER ASSEMBLY


    1. A01CHJQ

      Install the fuel filter assembly with the 2 bolts.

      Torque:
      18 N*m  { 180 kgf*cm, 13 ft.*lbf }
    2. A01CHCL

      Connect the 2 fuel hoses.

  6. INSTALL FUEL FILTER ELEMENT SUB-ASSEMBLY


    1. A01CHYJE02

      Install the fuel filter element sub-assembly to the fuel filter cover.

    2. Install the O-ring to the fuel filter cover.

    3. A01CHGGE02

      Install the fuel filter cover by turning it clockwise until the claw is engaged.

    4. A01CHNKE01

      Connect the level warning switch connector.

  7. BLEED AIR FROM FUEL SYSTEM


    1. A01CGS9

      Loosen the fuel filter's air bleed plug.

      Note


      • Do not use any tools.

      • Do not allow any fuel to spill.

      • If any fuel spills on any part of the engine, wipe it clean with a shop rag or a piece of cloth.

    2. A01CGKM

      While covering the drain pipe with a shop rag or a piece of cloth, press and release the priming pump until the fuel from the drain pipe does not have any bubbles.

    3. A01CIWK

      Tighten the air bleed plug.

      Note

      Do not use any tools.

  8. INSPECT FOR FUEL LEAK


    1. Perform the Active Test.


      1. Connect the intelligent tester to the DLC3.

      2. Start the engine.

      3. Turn the intelligent tester on.

      4. Select the following menu items: Powertrain / Engine / Active Test.

      5. Perform the Active Test.

        Intelligent Tester Display Test Details Control Range Diagnostic Notes
        Test the Fuel Leak Fuel leaks (common rail internal fuel pressure is raised) Stop/Start
        • Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2000 rpm when Start is selected.

        • Above conditions preserved while Start is selected.