ECD SYSTEM, Diagnostic DTC:P2032, P2033

DTC Code DTC Name
P2032 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 2)
P2033 Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 2)

DESCRIPTION

Refer to DTC P0545 Click here.

P2032
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 8 seconds

Sensor 2 output is less than 0.1 V for 8 seconds or more

(1 trip detection logic)


  • Open or short in exhaust gas temperature sensor (bank 1 sensor 2) circuit

  • Exhaust gas temperature sensor (bank 1 sensor 2)

  • ECM

P2033
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
30 minutes or more after the engine starts, the vehicle is driven at an engine speed of 1000 rpm or more.

Sensor 2 output is more than 4.95 V for 8 seconds or more

(1 trip detection logic)


  • Open or short in exhaust gas temperature sensor (bank 1 sensor 2) circuit

  • Exhaust gas temperature sensor (bank 1 sensor 2)

  • ECM

Tech Tips


  • Sensor 1 represents a sensor located upstream on the DPF catalytic converter.

  • Sensor 2 represents a sensor located downstream on the DPF catalytic converter.

  • After confirming DTCs P2032 and P2033, check the upstream and downstream exhaust gas temperature by selecting the following menus on the tester: Powertrain / Engine and ECT / Exhaust Temperature B1S1 and Exhaust Temperature B1S2.

    Result
    Condition Exhaust Gas Temperature Exhaust Gas Temperature Sensor Condition
    Idling after warm-up 50 to 700°C (122 to 1292°F) Normal
    1000°C (1832°F) Short circuit
    -40°C (-40°F) Open circuit

WIRING DIAGRAM

Refer to DTC P0545 Click here.

INSPECTION PROCEDURE

Note

After replacing the ECM, the new ECM needs registration Click here and initialization Click here.

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER (EXHAUST GAS TEMPERATURE)


    1. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the tester on.

    5. Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S2.

    6. Read the value.

      Standard
      Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after an engine speed of 3000 rpm is maintained for 1 minute.
      Result
      Temperature Displayed Proceed to
      -40°C (-40°F) A
      1000°C (1832°F) B
      OK: Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after maintaining the engine speed of 3000 rpm for 1 minute after accelerating the engine from idling to 3000 rpm C

      Tech Tips


      • If there is an open circuit, the intelligent tester will indicate -40°C (-40°F).

      • If there is a short circuit, the intelligent tester will indicate 1000°C (1832°F).


    B
    C
    A
  2. READ VALUE USING INTELLIGENT TESTER (OPEN IN WIRE HARNESS)


    1. A01CJ78E04
      Text in Illustration
      *1

      Exhaust Gas Temperature Sensor

      (Bank 1 Sensor 2)

      *2 ECM
      *a

      Front view of wire harness connector

      (to Exhaust Gas Temperature Sensor (Bank 1 Sensor 2))

      Disconnect the exhaust gas temperature sensor (bank 1 sensor 2) connector.

    2. Connect terminals 1 and 2 of the exhaust gas temperature sensor (bank 1 sensor 2) wire harness side connector.

    3. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    4. Connect the intelligent tester to the DLC3.

    5. Turn the ignition switch to ON.

    6. Turn the tester on.

    7. Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S2.

    8. Read the value.

      Standard
      1000°C (1832°F)
    9. Reconnect the exhaust gas temperature sensor (bank 1 sensor 2) connector.


    NG
    OK
  3. CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)


    1. Disconnect the exhaust gas temperature sensor (bank 1 sensor 2) connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      N4-1 - E37-5 (THCO) Always Below 1 Ω
      N4-2 - E35-14 (E21) Always Below 1 Ω
    4. Reconnect the exhaust gas temperature sensor (bank 1 sensor 2) connector.

    5. Reconnect the ECM connector.


    NG
    OK
  4. READ VALUE USING INTELLIGENT TESTER (SHORT IN WIRE HARNESS)


    1. A01CGKRE69
      Text in Illustration
      *1

      Exhaust Gas Temperature Sensor

      (Bank 1 Sensor 2)

      *2 ECM

      Disconnect the exhaust gas temperature sensor (bank 1 sensor 2) connector.

    2. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    3. Connect the intelligent tester to the DLC3.

    4. Turn the ignition switch to ON.

    5. Turn the tester on.

    6. Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S2.

    7. Read the value.

      Standard
      -40°C (-40°F)
    8. Reconnect the exhaust gas temperature sensor (bank 1 sensor 2) connector.


    NG
    OK
  5. CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)


    1. Disconnect the exhaust gas temperature sensor (bank 1 sensor 2) connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      N4-1 or E37-5 (THCO) - Body ground Always 10 kΩ or higher
      N4-2 or E35-14 (E21) - Body ground Always 10 kΩ or higher
    4. Reconnect the exhaust gas temperature sensor (bank 1 sensor 2) connector.

    5. Reconnect the ECM connector.


    NG
    OK