ECD SYSTEM, Diagnostic DTC:P1458, P1459

DTC Code DTC Name
P1458 EGR Actuator Minor Malfunction
P1459 EGR Actuator Major Malfunction

DESCRIPTION

P1458
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Warm up the engine and idle it for 1 second or more.

The EGR valve assembly outputs an abnormal signal a certain amount of times while the engine is running.

(1 trip detection logic)


  • Open or short in EGR valve assembly circuit

  • EGR valve assembly

  • ECM

P1459
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Warm up the engine and idle it for 1 second or more.

The EGR valve assembly outputs an abnormal signal a certain amount of times while the engine is running.

(1 trip detection logic)


  • Open or short in EGR valve assembly circuit

  • EGR valve assembly

  • ECM

WIRING DIAGRAM

A01CHVSE02

INSPECTION PROCEDURE

Note


  • After replacing the ECM, the new ECM needs registration Click here and initialization Click here.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tech Tips

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR


    1. Disconnect the EGR valve assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      E31-1 (E) - Body ground Always Below 1 Ω
    3. Reconnect the EGR valve assembly connector.


    NG
    OK
  2. CHECK EGR VALVE ASSEMBLY


    1. A01CILYE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to EGR Valve Assembly)

      Disconnect the EGR valve assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      E31-4 (+B) - Body ground Ignition switch ON 18 to 27 V
    3. Reconnect the EGR valve assembly connector.


    NG
    OK
  3. INSPECT EGR VALVE ASSEMBLY


    1. Inspect the EGR valve assembly Click here.


    NG
    OK
  4. CHECK DTC OUTPUT


    1. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the tester on.

    5. Clear the DTCs Click here.

    6. Turn the ignition switch off.

    7. Turn the ignition switch to ON.

    8. Enter the following menus: Powertrain / Engine and ECT / DTC.

    9. Read the DTCs.

      Result
      Result Proceed to
      DTC P1458 and/or P1459 is output A
      DTC is not output B

    B
    A
  5. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT
  6. CHECK DTC OUTPUT


    1. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the tester on.

    5. Clear the DTCs Click here.

    6. Turn the ignition switch off.

    7. Turn the ignition switch to ON.

    8. Enter the following menus: Powertrain / Engine and ECT / DTC.

    9. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC P1458 and/or P1459 is output B

    B
    A
  7. CHECK HARNESS AND CONNECTOR


    1. Disconnect the EGR valve assembly connector.

    2. Remove the ENG ACT relay from the engine room relay block and junction block.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      E31-4 (+B) - ENG ACT relay terminal 5 Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      E31-4 (+B) or ENG ACT relay terminal 5 - Body ground Always 10 kΩ or higher
    4. Reconnect the EGR valve assembly connector.

    5. Reinstall the ENG ACT relay.


    NG
    OK