ECD SYSTEM, Diagnostic DTC:P0545, P0546

DTC Code DTC Name
P0545 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 1)
P0546 Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 1)

DESCRIPTION

A01CJG6E02

The exhaust gas temperature sensors are installed in front of and behind the DPF (*1) catalytic converter to sense the exhaust gas temperature.

A thermistor built into the sensor changes its resistance value according to the exhaust gas temperature. The lower the exhaust gas temperature becomes, the greater the thermistor resistance value becomes. The higher the exhaust gas temperature becomes, the lower the thermistor resistance value becomes.

The exhaust gas temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the exhaust gas temperature sensor from terminals THCI (bank 1 sensor 1) and THCO (bank 1 sensor 2) via resistor R.

The resistor R and the exhaust gas temperature sensor are connected in series. When the resistance value of the exhaust gas temperature sensor changes in accordance with changes in the exhaust gas temperature, the voltage at terminals THCI (bank 1 sensor 1) and THCO (bank 1 sensor 2) also changes. Based on these signals, when DPF catalyst regeneration is needed, the ECM operates the injector to obtain target upstream temperature of the DPF catalytic converter as monitored through sensor 1. In addition, the ECM monitors the rate of DPF catalytic converter temperature increase using sensor 2.

*1: Diesel Particulate Filter

P0545
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 8 seconds Sensor 1 output is less than 0.1 V for 8 seconds or more (1 trip detection logic)
  • Open or short in exhaust gas temperature sensor (bank 1 sensor 1) circuit

  • Exhaust gas temperature sensor (bank 1 sensor 1)

  • ECM

P0546
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
30 minutes or more after the engine starts, the vehicle is driven at an engine speed of 1000 rpm or more. Sensor 1 output is more than 4.95 V for 8 seconds or more (1 trip detection logic)
  • Open or short in exhaust gas temperature sensor (bank 1 sensor 1) circuit

  • Exhaust gas temperature sensor (bank 1 sensor 1)

  • ECM

Tech Tips


  • Sensor 1 represents a sensor located upstream of the DPF catalytic converter.

  • Sensor 2 represents a sensor located downstream of the DPF catalytic converter.

  • After confirming DTCs P0545, P0546, P2032, and P2033, check the upstream and downstream exhaust gas temperature by selecting the following menus on the tester: Powertrain / Engine and ECT / Exhaust Temperature B1S1 and Exhaust Temperature B1S2.

    Result
    Condition Exhaust Gas Temperature Exhaust Gas Temperature Sensor Condition
    Idling after warm-up 50 to 700°C (122 to 1292°F) Normal
    -40°C (-40°F) Open circuit
    1000°C (1832°F) Short circuit

WIRING DIAGRAM

A01CJC8E02

INSPECTION PROCEDURE

Note

After replacing the ECM, the new ECM needs registration Click here and initialization Click here.

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER (EXHAUST GAS TEMPERATURE)


    1. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the tester on.

    5. Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S1.

    6. Read the value.

      Standard
      Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after an engine speed of 3000 rpm is maintained for 1 minute.
      Result
      Temperature Displayed Proceed to
      -40°C (-40°F) A
      1000°C (1832°F) B
      OK: Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after maintaining the engine speed of 3000 rpm for 1 minute after accelerating the engine from idling to 3000 rpm C

      Tech Tips


      • If there is an open circuit, the intelligent tester will indicate -40°C (-40°F).

      • If there is a short circuit, the intelligent tester will indicate 1000°C (1832°F).


    B
    C
    A
  2. READ VALUE USING INTELLIGENT TESTER (OPEN IN WIRE HARNESS)


    1. A01CHB2E04
      Text in Illustration
      *1

      Exhaust Gas Temperature Sensor

      (Bank 1 Sensor 1)

      *2 ECM
      *a

      Front view of wire harness connector

      (to Exhaust Gas Temperature Sensor (Bank 1 Sensor 1))

      Disconnect the exhaust gas temperature sensor (bank 1 sensor 1) connector.

    2. Connect terminals 1 and 2 of the exhaust gas temperature sensor wire harness side connector.

    3. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    4. Connect the intelligent tester to the DLC3.

    5. Turn the ignition switch to ON.

    6. Turn the tester on.

    7. Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S1.

    8. Read the value.

      Standard
      1000°C (1832°F)
    9. Reconnect the exhaust gas temperature sensor (bank 1 sensor 1) connector.


    NG
    OK
  3. CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)


    1. Disconnect the exhaust gas temperature sensor (bank 1 sensor 1) connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      E34-1 - E37-11 (THCI) Always Below 1 Ω
      E34-2 - E35-14 (E21) Always Below 1 Ω
    4. Reconnect the exhaust gas temperature sensor (bank 1 sensor 1) connector.

    5. Reconnect the ECM connector.


    NG
    OK
  4. READ VALUE USING INTELLIGENT TESTER (SHORT IN WIRE HARNESS)


    1. A01CGKRE68
      Text in Illustration
      *1

      Exhaust Gas Temperature Sensor

      (Bank 1 Sensor 1)

      *2 ECM

      Disconnect the exhaust gas temperature sensor (bank 1 sensor 1) connector.

    2. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    3. Connect the intelligent tester to the DLC3.

    4. Turn the ignition switch to ON.

    5. Turn the tester on.

    6. Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S1.

    7. Read the value.

      Standard
      -40°C (-40°F)
    8. Reconnect the exhaust gas temperature sensor connector.


    NG
    OK
  5. CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)


    1. Disconnect the exhaust gas temperature sensor (bank 1 sensor 1) connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      E34-1 or E37-11 (THCI) - Body ground Always 10 kΩ or higher
      E34-2 or E35-14 (E21) - Body ground Always 10 kΩ or higher
    4. Reconnect the exhaust gas temperature sensor (bank 1 sensor 1) connector.

    5. Reconnect the ECM connector.


    NG
    OK