ECD SYSTEM, Diagnostic DTC:P0488

DTC Code DTC Name
P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance

DESCRIPTION

The throttle control motor opens and closes the throttle valve according to a duty-cycle (signal) from the ECM.

P0488
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state.

Condition (a) or (b) continues for more than 1 second

(a) Battery voltage is 18 V or more


  • Throttle motor's activation duty is not within the normal range (Activation duty: 10 to 90)

(b) Open, short or stuck in throttle sensor


  • Open or short in throttle control motor circuit

  • Throttle control motor (built into diesel throttle body assembly)

  • ECM

WIRING DIAGRAM

A01CIS2E01

INSPECTION PROCEDURE

Note

After replacing the ECM, the new ECM needs registration Click here and initialization Click here.

Tech Tips

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.

PROCEDURE


  1. CHECK THROTTLE CONTROL MOTOR (VCR VOLTAGE)


    1. A01CJA3E06
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Throttle Control Motor)

      Disconnect the throttle control motor connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      T10-2 (VCR) - Body ground Ignition switch ON 18 to 27 V
    4. Reconnect the throttle control motor connector.


    NG
    OK
  2. CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM)


    1. Disconnect the throttle control motor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      T10-1 (VTAR) - E37-16 (LUSL) Always Below 1 Ω
      T10-3 (E2R) - Body ground Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      T10-1 (VTAR) or E37-16 (LUSL) - Body ground Always 10 kΩ or higher
    4. Reconnect the throttle control motor connector.

    5. Reconnect the ECM connector.


    NG
    OK
  3. REPLACE DIESEL THROTTLE BODY ASSEMBLY (THROTTLE CONTROL MOTOR)


    1. Replace the diesel throttle body assembly Click here.

    2. Perform diesel throttle body assembly initialization Click here.


    NEXT
  4. CHECK DTC OUTPUT


    1. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the tester on.

    5. Clear the DTCs Click here.

    6. Turn the ignition switch off.

    7. Start the engine.

    8. Perform the following repeatedly for 1 minute.

    9. Gradually raise the engine speed to 3000 rpm from idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state.

    10. Enter the following menus: Powertrain / Engine and ECT / DTC.

    11. Read the DTCs.

      Result
      Result Proceed to
      DTC P0488 is output A
      DTC is not output B

    B
    A