ECD SYSTEM, Diagnostic DTC:P0340

DTC Code DTC Name
P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)

DESCRIPTION

The camshaft position sensor (G signal) consists of a magnet and MR element.

The camshaft drive gear has 5 teeth on its inner circumference. When the camshaft drive gear rotates, the air gap changes between the protrusion on the gear and the pickup coil. The change affects the magnetic field and results in change in the resistance of the MR element. The crankshaft angle sensor plate has 34 teeth and outputs 34 signals every engine revolution. The ECM detects the standard crankshaft angle based on the G signal and actual crankshaft angle and engine speed by the NE signal.

P0340
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Crank engine for 4 seconds (STA on)

STA ON:

No camshaft position sensor signal to ECM while cranking for 4 seconds or more (2 trip detection logic).


  • Open or short in camshaft position sensor circuit

  • Camshaft position sensor

  • Camshaft (camshaft drive gear)

  • ECM

Idle engine for 1 second (STA off)

STA OFF:

No camshaft position sensor signal to ECM with engine speed 650 to 3000 rpm 20 times or more (2 trip detection logic).

WIRING DIAGRAM

Refer to DTC P0335 Click here.

INSPECTION PROCEDURE

Note

After replacing the ECM, the new ECM needs registration Click here and initialization Click here.

Tech Tips

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.

PROCEDURE


  1. CHECK CAMSHAFT POSITION SENSOR


    1. A01CH2QE03
      Text in Illustration
      *a

      Component with harness connected

      (ECM)

      *b G and NE Signal Waveform
      *c 5 V/DIV.
      *d 20 ms./DIV. (Idling)

      While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

      Standard
      Tester Connection Specified Condition
      E37-7 (NE+) - E37-8 (NE-) Correct waveform appears as shown
      E37-13 (G+) - E37-14 (G-) Correct waveform appears as shown

    NG
    OK
  2. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)


    1. Disconnect the camshaft position sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      C11-1 (G1) - E37-13 (G+) Always Below 1 Ω
      C11-2 (G-) - E37-14 (G-) Always Below 1 Ω
      C11-3 (VG) - E37-15 (VCG) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      C11-1 (G1) or E37-13 (G+) - Body ground Always 10 kΩ or higher
      C11-2 (G-) or E37-14 (G-) - Body ground Always 10 kΩ or higher
      C11-3 (VG) or E37-15 (VCG) - Body ground Always 10 kΩ or higher
    4. Reconnect the camshaft position sensor connector.

    5. Reconnect the ECM connector.


    NG
    OK
  3. CHECK ECM (VCG VOLTAGE)


    1. A01CIKSE03
      Text in Illustration
      *a

      Component with harness connected

      (ECM)

      Turn the ignition switch to ON.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      E37-15 (VCG) - E37-14 (G-) Ignition switch ON 4.5 to 5.5 V

    NG
    OK
  4. CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)

    A01CIX2E40
    OK
    The camshaft position sensor is installed properly.

    NG
    OK
  5. INSPECT CAMSHAFT (CAMSHAFT DRIVE GEAR)


    1. Check the teeth of the camshaft drive gear.


    NG
    OK
  6. REPLACE CAMSHAFT POSITION SENSOR


    1. Replace the camshaft position sensor Click here.


    NEXT
  7. CHECK DTC OUTPUT


    1. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the tester on.

    5. Start the engine.

    6. Enter the following menus: Powertrain / Engine and ECT / DTC.

    7. Read the DTCs.

      Result
      Result Proceed to
      DTC P0340 is output A
      DTC is not output B

    B
    A