ECD SYSTEM, Diagnostic DTC:P0107, P0108

DTC Code DTC Name
P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input
P0108 Manifold Absolute Pressure / Barometric Pressure Circuit High Input

DESCRIPTION

Using a built-in sensor unit, the manifold absolute pressure sensor detects the intake manifold pressure and outputs it as a voltage. The ECM then determines the basic injection duration and basic ignition advance angle based on this voltage.

Since the manifold absolute pressure sensor does not use the atmospheric pressure as a criterion, but senses the absolute pressure inside the intake manifold (the pressure in proportion to the preset absolute vacuum 0), it is not influenced by fluctuations in the atmospheric pressure due to high altitude and other factors. This permits the system to maintain the air fuel ratio at the proper level under all conditions.

A01CGRCE15
P0107
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
2 seconds after engine is started, race engine for 1 second

After the engine is started, condition (a) continues for more than 0.5 seconds (1 trip detection logic):

(a) Manifold absolute pressure sensor voltage is 0.1 V or less.


  • Open or short in manifold absolute pressure sensor circuit

  • Manifold absolute pressure sensor

  • ECM

P0108
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
2 seconds after engine is started, race engine for 1 second

After the engine is started, condition (a) continues for more than 0.5 seconds (1 trip detection logic):

(a) Manifold absolute pressure sensor voltage is 4.8 V or higher.


  • Open or short in manifold absolute pressure sensor circuit

  • Manifold absolute pressure sensor

  • ECM

Tech Tips

If DTC P0107 or P0108 is detected, check the intake manifold pressure by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / MAP.

Intake Manifold Pressure (kPa) Malfunction
Approximately 0 Short in PIM or E2 circuit
255
  • Short in VC or PIM circuit

  • Open in PIM circuit

  • Open in E2 circuit

WIRING DIAGRAM

A01CIGJE01

INSPECTION PROCEDURE

Note

After replacing the ECM, the new ECM needs registration Click here and initialization Click here.

Tech Tips


  • If different DTCs are output and those DTCs are related to different systems which use terminal E2 as a ground terminal, there may be an open circuit between terminal E2 and ground.

  • Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER (MANIFOLD ABSOLUTE PRESSURE)


    1. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the tester on.

    5. Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.

    6. Read the value.

      OK
      Same value as the actual atmospheric pressure.

      Tech Tips


      • Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. This varies by weather (high atmospheric pressure, low atmospheric pressure).

      • As the measurement range of the sensor is 40 to 320 kPa (300 to 2400 mmHg, 11.8 to 94.5 in.Hg), if the elevation is too high, the output value of the sensor may not be correct.

      • Also, check "Atmospheric Pressure" in the Data List.

      Result
      Result Proceed to
      NG A
      OK B

    B
    A
  2. CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)


    1. Disconnect the manifold absolute pressure sensor connector.

    2. Disconnect the ECM connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      V9-2 (PIM) - E36-5 (PIM) Always Below 1 Ω
      V9-3 (VC) - E36-13 (VC) Always Below 1 Ω
      V9-1 (E) - E36-14 (E2) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      V9-2 (PIM) or E36-5 (PIM) - Body ground Always 10 kΩ or higher
      V9-3 (VC) or E36-13 (VC) - Body ground Always 10 kΩ or higher
    4. Reconnect the manifold absolute pressure sensor connector.

    5. Reconnect the ECM connectors.


    NG
    OK
  3. CHECK ECM (VC VOLTAGE)


    1. A01CIKSE01
      Text in Illustration
      *a

      Component with harness connected

      (ECM)

      Turn the ignition switch to ON.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      E36-13 (VC) - E36-14 (E2) Ignition switch ON 4.5 to 5.5 V

    NG
    OK
  4. REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR


    1. Replace the manifold absolute pressure sensor.


    NEXT
  5. CHECK WHETHER DTC OUTPUT RECURS


    1. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    2. Connect the intelligent tester to the DLC3.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off for 30 seconds or more.

    5. Turn the tester off.

    6. Start the engine.

    7. After the engine is started for 2 seconds, race the engine for 1 second.

    8. Turn the tester on.

    9. Enter the following menus: Powertrain / Engine and ECT / DTC.

    10. Read the DTCs using the intelligent tester.

      Result
      Display (DTC output) Proceed to
      DTC P0107 and/or P0108 are output A
      DTC is not output B

    B
    A
  6. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT
  7. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.


    NEXT
  8. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    2. Connect the intelligent tester to the DLC3.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off for 30 seconds or more.

    5. Turn the tester off.

    6. Turn the ignition switch to ON for 3 seconds and turn the tester on.

    7. After the engine is started for 2 seconds, race the engine for 1 second.

    8. Confirm that the DTC is not output again.

      Tech Tips

      Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


      1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

      2. Input DTC P0107 or P0108.

      3. Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, race the engine for 1 minute, and then idle the engine for 5 minutes.


    NEXT