ECD SYSTEM, Diagnostic DTC:P2031, P2032, P2033

DTC Code DTC Name
P2031 Exhaust Gas Temperature Sensor Circuit (Bank 1 Sensor 2)
P2032 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 2)
P2033 Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 2)

DESCRIPTION

Refer to DTC P0544 Click here.

DTC No. DTC Detection Condition Trouble Area
P2031 Sensor 2 output is less than 0.2 V or more than 4.95 V for 8 seconds or more (1 trip detection logic)
  • Open or short in exhaust gas temperature sensor (bank 1 sensor 2) circuit

  • Exhaust gas temperature sensor (bank 1 sensor 2)

  • ECM

P2032

Sensor 2 output is less than 0.2 V for 8 seconds or more

(1 trip detection logic)


  • Open or short in exhaust gas temperature sensor (bank 1 sensor 2) circuit

  • Exhaust gas temperature sensor (bank 1 sensor 2)

  • ECM

P2033

Sensor 2 output is more than 4.95 V for 8 seconds or more

(1 trip detection logic)


  • Open or short in exhaust gas temperature sensor (bank 1 sensor 2) circuit

  • Exhaust gas temperature sensor (bank 1 sensor 2)

  • ECM

Tech Tips


  • Sensor 1 represents a sensor located upstream on the DPF catalytic converter.

  • Sensor 2 represents a sensor located downstream on the DPF catalytic converter.

  • After confirming DTC P2031, P2032, and P2033, check the upstream and downstream exhaust gas temperature by selecting the following menus on the tester: Powertrain / Engine and ECT / Exhaust Temperature B1S1 and Exhaust Temperature B2S1.

    Result
    Condition Exhaust Gas Temperature Exhaust Gas Temperature Sensor Condition
    Idling after warm-up Constant at 50 to 700°C (122 to 1292°F) Normal
    1000°C (1832°F) Short circuit
    0°C (32°F) Open circuit

WIRING DIAGRAM

Refer to DTC P0544 Click here.

INSPECTION PROCEDURE

Note

After replacing the ECM, the new ECM needs registration Click here and initialization Click here.

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER (EXHAUST GAS TEMPERATURE)


    1. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the tester on.

    5. Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S2.

    6. Read the value.

      Standard
      Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after an engine speed of 3000 rpm is maintained for 1 minute.
      Result
      Temperature Displayed Proceed to
      0°C (32°F) (After warming up the engine) A
      1000°C (1832°F) B
      OK: Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after maintaining the engine speed of 3000 rpm for 1 minute after accelerating the engine from idling to 3000 rpm C

      Tech Tips


      • If there is an open circuit, the intelligent tester will indicate 0°C (32°F).

      • If there is a short circuit, the intelligent tester will indicate 1000°C (1832°F).


    B
    C
    A
  2. READ VALUE USING INTELLIGENT TESTER (OPEN IN WIRE HARNESS)


    1. A01CJ78E03
      Text in Illustration
      *1

      Exhaust Gas Temperature Sensor

      (Bank 1 Sensor 2)

      *2 ECM
      *3

      Front view of wire harness connector

      (to Exhaust Gas Temperature Sensor (Bank 1 Sensor 2))

      Disconnect the exhaust gas temperature sensor (bank 1 sensor 2) connector.

    2. Connect terminals 1 and 2 of the exhaust gas temperature sensor (bank 1 sensor 2) wire harness side connector.

    3. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    4. Connect the intelligent tester to the DLC3.

    5. Turn the ignition switch to ON.

    6. Turn the tester on.

    7. Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S2.

    8. Read the value.

      Standard
      1000°C (1832°F)
    9. Reconnect the exhaust gas temperature sensor (bank 1 sensor 2) connector.


    NG
    OK
  3. READ VALUE USING INTELLIGENT TESTER (OPEN IN ECM)


    1. A01CH16E50
      Text in Illustration
      *1

      Exhaust Gas Temperature Sensor

      (Bank 1 Sensor 2)

      *2 ECM
      *3

      Component with harness connected

      (ECM)

      Disconnect the exhaust gas temperature sensor (bank 1 sensor 2) connector.

    2. Connect terminals THCO and E2 of the ECM connectors.

      Tech Tips

      Before checking, do a visual and contact pressure check on the ECM connector.

    3. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    4. Connect the intelligent tester to the DLC3.

    5. Turn the ignition switch to ON.

    6. Turn the tester on.

    7. Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S2.

    8. Read the value.

      Standard
      1000°C (1832°F)
    9. Reconnect the exhaust gas temperature sensor (bank 1 sensor 2) connector.


    NG
    OK
  4. READ VALUE USING INTELLIGENT TESTER (SHORT IN WIRE HARNESS)


    1. A01CGKRE63
      Text in Illustration
      *1

      Exhaust Gas Temperature Sensor

      (Bank 1 Sensor 2)

      *2 ECM

      Disconnect the exhaust gas temperature sensor (bank 1 sensor 2) connector.

    2. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    3. Connect the intelligent tester to the DLC3.

    4. Turn the ignition switch to ON.

    5. Turn the tester on.

    6. Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S2.

    7. Read the value.

      Standard
      0°C (32°F)
    8. Reconnect the exhaust gas temperature sensor (bank 1 sensor 2) connector.


    NG
    OK
  5. READ VALUE USING INTELLIGENT TESTER (SHORT IN ECM)


    1. A01CIZ8E08
      Text in Illustration
      *1

      Exhaust Gas Temperature Sensor

      (Bank 1 Sensor 2)

      *2 ECM
      *3

      Rear view of wire harness connector

      (to ECM)

      Disconnect the exhaust gas temperature sensor (bank 1 sensor 2) connector.

    2. Disconnect the ECM connector.

    3. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    4. Connect the intelligent tester to the DLC3.

    5. Turn the ignition switch to ON.

    6. Turn the tester on.

    7. Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S2.

    8. Read the value.

      Standard
      0°C (32°F)
    9. Reconnect the exhaust gas temperature sensor (bank 1 sensor 2) connector.

    10. Reconnect the ECM connector.


    NG
    OK