ECD SYSTEM, Diagnostic DTC:P2002

DTC Code DTC Name
P2002 Particulate Trap Efficiency Below Threshold (Bank1)

DESCRIPTION

A DPF (Diesel Particulate Filter) catalyst is located in the center exhaust pipe assembly. A wall-flow type DPF catalyst, which filters all exhaust gas through ceramic walls with high heat resistance, is used to allow the exhaust gas to be organized by the catalyst when flowing through the porous ceramic structure, reducing PM (Particulate Matter) drastically.

A01CIAGE01
DTC No. DTC Detection Condition Trouble Area
P2002
  • Differential pressure sensor assembly detects abnormally high differential pressure while vehicle is running.

  • Exhaust gas temperature sensor detects abnormally high temperature while vehicle is running.

  • Vehicle is driven continuously without performing forcible regeneration function although DPF switch assembly light is blinking, and amount of accumulated PM exceeds specified value.

  • During forcible regeneration function, temperature of center exhaust pipe assembly (catalyst converter) does not increase although injection volume is as specified.


  • Exhaust gas temperature sensor

  • Differential pressure sensor assembly

  • Center exhaust pipe assembly (DPF catalyst converter)

  • Open or short in differential pressure sensor assembly circuit

  • Open or short in exhaust gas temperature sensor circuit

  • ECM

INSPECTION PROCEDURE

Note

After replacing the ECM, the new ECM needs registration Click here and initialization Click here.

Tech Tips


  • Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.

  • If the amount of accumulated PM exceeds the specified value, DTC P2002 is set and the system enters fail-safe mode, in which the system limits the engine power.

  • Check the amount of engine oil after troubleshooting is finished.

  • If the amount of engine oil is more than the specified level, replace the engine oil.

PROCEDURE


  1. INSPECT DPF SWITCH ASSEMBLY


    1. Use the table below to troubleshoot each problem symptom.

      Result
      Condition Proceed to
      DPF switch assembly light is not blinking A
      DPF switch assembly light is blinking B

    B
    A
  2. CHECK OTHER DTC OUTPUT


    1. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the tester on.

    5. Enter the following menus: Powertrain / Engine and ECT / DTC.

    6. Read the DTCs.

      Result
      Result Proceed to
      DTC P2002 is output A
      DTC P2002 and other DTCs are output B

    B
    A
  3. READ VALUE USING FREEZE FRAME DATA (EXHAUST GAS TEMPERATURE)


    1. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the tester on.

    5. Enter the following menus: Powertrain / Engine and ECT / DTC / P2002.

    6. Read the value.

      Result
      Item Exhaust Temperature Proceed to
      Exhaust Temperature B1S1 Less than 740°C (1364°F) A
      Exhaust Temperature B1S2 Less than 940°C (1724°F) A
      Exhaust Temperature B1S1 740°C (1364°F) or more B
      Exhaust Temperature B1S2 940°C (1724°F) or more C

      Tech Tips

      When troubleshooting abnormal temperature detection by exhaust gas temperature sensor (upstream), check that the hose between the turbocharger sub-assembly and the intake manifold is connected properly.


    B
    C
    A
  4. READ VALUE USING FREEZE FRAME DATA (DIFFERENTIAL PRESSURE)


    1. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the tester on.

    5. Enter the following menus: Powertrain / Engine and ECT / DTC / P2002.

    6. Read the value.

      Result
      Item Differential Pressure Proceed to
      DPF Differential Pressure 15 kPa or less A
      DPF Differential Pressure 15 kPa or more B

    B
    A
  5. READ VALUE USING INTELLIGENT TESTER (DIFFERENTIAL PRESSURE)


    1. Warm up the engine.

    2. Disconnect the negative battery terminal and wait for at least 1 minute.

    3. Reconnect the negative battery terminal.

    4. Initialize the learning value of the injector or supply pump assembly Click here.

      Tech Tips

      Perform initialization with the engine warmed up (engine coolant temperature is 60°C (140°F) or more and fuel temperature is 20°C (68°F) or more).

    5. Initialize the learning value of the diesel throttle body assembly Click here.

    6. Allow the engine to idle for at least 5 minutes.

    7. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    8. Connect the intelligent tester to the DLC3.

    9. Turn the ignition switch to ON.

    10. Turn the tester on.

    11. Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.

      Tech Tips


      • If the exhaust gas temperature is high, the differential pressure cannot be measured correctly.

      • If the differential pressure is outside the normal range, the monolithic converter assembly may have deteriorated or the monolithic converter assembly may be clogged with PM.

      • If DTC P2002 is set, the engine speed cannot be raised to the high-speed range because the engine output limiting control is performed. If this occurs, replace the center exhaust pipe assembly (catalyst converter) Click here.

      • If DTC P2002 is set, be sure to clear the DTCs.

      Result
      Engine Speed (no engine load) Differential Pressure Proceed to
      3500 to 3600 rpm (Exhaust Temperature B1S1 is 200°C (392°F) or less) 30 kPa or more A
      3500 to 3600 rpm (Exhaust Temperature B1S1 is 200°C (392°F) or less) 30 kPa or less B

    B
    A
  6. CLEAN EXHAUST SYSTEM


    1. Clean the catalytic center exhaust pipe assembly (catalyst converter) Click here.


    NEXT
  7. READ VALUE USING INTELLIGENT TESTER (DIFFERENTIAL PRESSURE)


    1. Allow the engine to idle for at least 5 minutes.

    2. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    3. Connect the intelligent tester to the DLC3.

    4. Turn the ignition switch to ON.

    5. Turn the tester on.

    6. Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.

      Tech Tips


      • If the exhaust gas temperature is high, the differential pressure cannot be measured correctly.

      • If the differential pressure is outside the normal range, the center exhaust pipe assembly (catalyst converter) may have deteriorated or the center exhaust pipe assembly (catalyst converter) may be clogged with PM.

      • If DTC P2002 is set, the engine speed cannot be raised to the high-speed range because the engine output limiting control is performed. If this occurs, replace the center exhaust pipe assembly (catalyst converter) Click here.

      • If DTC P2002 is set, be sure to clear the DTCs.

      Result
      Engine Speed (no engine load) Differential Pressure Proceed to
      3500 to 3600 rpm (Exhaust Temperature B1S1 is 200°C (392°F) or less) 30 kPa or less A
      3500 to 3600 rpm (Exhaust Temperature B1S1 is 200°C (392°F) or less) 30 kPa or more B

    B
    A
  8. READ VALUE USING INTELLIGENT TESTER (DIFFERENTIAL PRESSURE)


    1. Perform the forcible regeneration function Click here.

    2. After the forcible regeneration is completed, allow the engine to idle for at least 5 minutes.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.

    4. Check the differential pressure when the exhaust gas temperature sensor indicates 200°C (392°F) or less.

      Result
      Engine Speed (no engine load) Differential Pressure Proceed to
      3500 to 3600 rpm (Exhaust Temperature B1S1 is 200°C (392°F) or less) 15 kPa or less A
      3500 to 3600 rpm (Exhaust Temperature B1S1 is 200°C (392°F) or less) 15 kPa or more B

    B
    A
  9. READ VALUE USING INTELLIGENT TESTER (DIFFERENTIAL PRESSURE)


    1. Perform the forcible regeneration function Click here.

    2. After the forcible regeneration is completed, allow the engine to idle for at least 5 minutes.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.

    4. Check the differential pressure when the exhaust gas temperature sensor indicates 200°C (392°F) or less.

      Result
      Engine Speed (no engine load) Differential Pressure Proceed to
      3500 to 3600 rpm (Exhaust Temperature B1S1 is 200°C (392°F) or less) 15 kPa or less A
      3500 to 3600 rpm (Exhaust Temperature B1S1 is 200°C (392°F) or less) 15 kPa or more B

    B
    A