CAN COMMUNICATION SYSTEM, Diagnostic DTC:U0073, U0105/23

DTC Code DTC Name
U0073 Control Module Communication Bus Off
U0105/23 Lost Communication With Fuel Injector Control Module

DESCRIPTION


DTC Code DTC Detection Condition Trouble Area
U0073 Control Module Communication Bus Off
  • Control bus circuit

  • ECM CAN main wire or connector

  • Electric vehicle control ECU assembly CAN branch wire or connector

  • Brake actuator assembly (skid control ECU) CAN branch wire or connector

  • Combination meter assembly CAN main wire or connector

  • ECM

  • Electric vehicle control ECU assembly

  • Brake actuator assembly (skid control ECU)

  • Combination meter assembly

  • No. 1 junction connector

  • No. 2 junction connector

  • No. 3 junction connector

  • No. 6 junction connector

U0105/23 Lost Communication with ECM

WIRING DIAGRAM

A01CIC2E03

INSPECTION PROCEDURE

Tech Tips

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.


    NEXT
  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.


    NEXT
  3. CHECK CAN BUS WIRE (CHECK CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)


    1. A01CHZVE04
      Text in Illustration
      *a

      Component with harness connected

      (Combination Meter Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition Resistance: Malfunction
      C19-14 (CANH) - C19-13 (CANL) Ignition switch off 54 to 69 Ω Below 53 Ω: Short in line
      C19-14 (CANH) - C19-13 (CANL) Ignition switch off 54 to 69 Ω Higher than 70 Ω: Open in CAN main bus line
      C19-14 (CANH) - C18-40 (B) Ignition switch off 6 kΩ or higher Below 6 kΩ: +B short
      C19-13 (CANL) - C18-40 (B) Ignition switch off 6 kΩ or higher Below 6 kΩ: +B short
      C19-14 (CANH) - C18-36 (SE) Ignition switch off 200 Ω or higher Below 200 Ω: Ground short
      C19-13 (CANL) - C18-36 (SE) Ignition switch off 200 Ω or higher Below 200 Ω: Ground short
      Result
      Result Proceed to

      NG


      • Open in CAN main bus line

      A

      NG


      • Short in line

      • +B short

      • GND short

      B
      OK C

    B
    C
    A
  4. CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    1. A01CGO1E47
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Disconnect the No. 1 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      J76-8 (CANH) - J76-19 (CANL) Ignition switch off 108 to 132 Ω

    NG
    OK
  5. CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM)


    1. A01CGO1E48
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      J76-7 (CANH) - J76-18 (CANL) Ignition switch off 108 to 132 Ω

    NG
    OK
  6. CONNECT CONNECTOR


    1. Reconnect the J76 No. 1 junction connector.


    NEXT
  7. CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 1 JUNCTION CONNECTOR)


    1. A01CH7UE07
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to ECM)

      Disconnect the ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E40-8 (CANP) - E40-2 (CANN) Ignition switch off 108 to 132 Ω

    NG
    OK
  8. CONNECT CONNECTOR


    1. Reconnect the J76 No. 1 junction connector.


    NEXT
  9. CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)


    1. A01CGO1E49
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Disconnect the No. 2 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      J72-7 (CANH) - J72-18 (CANL) Ignition switch off 108 to 132 Ω

    NG
    OK
  10. CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    1. A01CGO1E50
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      J72-8 (CANH) - J72-19 (CANL) Ignition switch off 108 to 132 Ω

    NG
    OK
  11. CONNECT CONNECTOR


    1. Reconnect the J72 No. 2 junction connector.


    NEXT
  12. CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    1. A01CGO1E51
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      Disconnect the No. 3 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      J82-1 (CANH) - J82-12 (CANL) Ignition switch off 108 to 132 Ω

    NG
    OK
  13. CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    1. A01CGO1E52
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      J82-4 (CANH) - J82-15 (CANL) Ignition switch off 108 to 132 Ω

    NG
    OK
  14. CONNECT CONNECTOR


    1. Reconnect the J82 No. 3 junction connector.


    NEXT
  15. CHECK FOR OPEN IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)


    1. A01CIQSE27
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 6 Junction Connector)

      Disconnect the No. 6 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      J58-3 (CANH) - J58-8 (CANL) Ignition switch off 108 to 132 Ω

    NG
    OK
  16. CHECK FOR OPEN IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    1. A01CIQSE28
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 6 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      J58-5 (CANH) - J58-10 (CANL) Ignition switch off 108 to 132 Ω

    NG
    OK
  17. CONNECT CONNECTOR


    1. Reconnect the J58 No. 6 junction connector.


    NEXT
  18. CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 6 JUNCTION CONNECTOR)


    1. A01CHMGE05
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Combination Meter Assembly)

      Disconnect the combination meter assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      C19-14 (CANH) - C19-13 (CANL) Ignition switch off 108 to 132 Ω

    NG
    OK
  19. CHECK FOR SHORT IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE)


    1. A01CHZVE04
      Text in Illustration
      *a

      Component with harness connected

      (Combination Meter Assembly)

      Disconnect the J76 No. 1 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      C19-14 (CANH) - C19-13 (CANL) Ignition switch off 108 to 132 Ω
      C19-14 (CANH) - C18-36 (SE) Ignition switch off 200 Ω or higher
      C19-13 (CANL) - C18-36 (SE) Ignition switch off 200 Ω or higher
      C19-14 (CANH) - C18-40 (B) Ignition switch off 6 kΩ or higher
      C19-13 (CANL) - C18-40 (B) Ignition switch off 6 kΩ or higher

    NG
    OK
  20. CHECK FOR SHORT IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ELECTRIC VEHICLE CONTROL ECU ASSEMBLY)


    1. A01CGV9E52
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      *b Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      J76-9 (CANH) - J76-20 (CANL) Ignition switch off 200 Ω or higher
      J76-10 (CANH) - J76-21 (CANL) Ignition switch off 200 Ω or higher
      J76-9 (CANH) - D34-4 (CG) Ignition switch off 200 Ω or higher
      J76-20 (CANL) - D34-4 (CG) Ignition switch off 200 Ω or higher
      J76-10 (CANH) - D34-4 (CG) Ignition switch off 200 Ω or higher
      J76-21 (CANL) - D34-4 (CG) Ignition switch off 200 Ω or higher
      J76-9 (CANH) - D34-16 (BAT) Ignition switch off 6 kΩ or higher
      J76-20 (CANL) - D34-16 (BAT) Ignition switch off 6 kΩ or higher
      J76-10 (CANH) - D34-16 (BAT) Ignition switch off 6 kΩ or higher
      J76-21 (CANL) - D34-16 (BAT) Ignition switch off 6 kΩ or higher

    NG
    OK
  21. CHECK FOR SHORT IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM)


    1. A01CGV9E53
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      *b Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      J76-7 (CANH) - J76-18 (CANL) Ignition switch off 108 to 132 Ω
      J76-7 (CANH) - D34-4 (CG) Ignition switch off 200 Ω or higher
      J76-18 (CANL) - D34-4 (CG) Ignition switch off 200 Ω or higher
      J76-7 (CANH) - D34-16 (BAT) Ignition switch off 6 kΩ or higher
      J76-18 (CANL) - D34-16 (BAT) Ignition switch off 6 kΩ or higher

    NG
    OK
  22. CONNECT CONNECTOR


    1. Reconnect the J76 No. 1 junction connector.


    NEXT
  23. CHECK FOR SHORT IN CAN BUS WIRE (ELECTRIC VEHICLE CONTROL ECU ASSEMBLY)


    1. A01CGL4E03
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Electric Vehicle Control ECU Assembly)

      *b Front view of DLC3

      Disconnect the electric vehicle control ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E41-6 (CA1+) - E41-7 (CA1-) Ignition switch off 54 to 69 Ω
      E41-2 (CA2+) - E41-3 (CA2-) Ignition switch off 54 to 69 Ω
      E41-6 (CA1+) - D34-4 (CG) Ignition switch off 200 Ω or higher
      E41-7 (CA1-) - D34-4 (CG) Ignition switch off 200 Ω or higher
      E41-2 (CA2+) - D34-4 (CG) Ignition switch off 200 Ω or higher
      E41-3 (CA2-) - D34-4 (CG) Ignition switch off 200 Ω or higher
      E41-6 (CA1+) - D34-16 (BAT) Ignition switch off 6 kΩ or higher
      E41-7 (CA1-) - D34-16 (BAT) Ignition switch off 6 kΩ or higher
      E41-2 (CA2+) - D34-16 (BAT) Ignition switch off 6 kΩ or higher
      E41-3 (CA2-) - D34-16 (BAT) Ignition switch off 6 kΩ or higher

    NG
    OK
  24. CONNECT CONNECTOR


    1. Reconnect the J76 No. 1 junction connector.


    NEXT
  25. CHECK FOR SHORT IN CAN BUS WIRE (ECM)


    1. A01CGXGE04
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to ECM)

      *b Front view of DLC3

      Disconnect the ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E40-8 (CANP) - E40-2 (CANN) Ignition switch off 108 to 132 Ω
      E40-8 (CANP) - D34-4 (CG) Ignition switch off 200 Ω or higher
      E40-2 (CANN) - D34-4 (CG) Ignition switch off 200 Ω or higher
      E40-8 (CANP) - D34-16 (BAT) Ignition switch off 6 kΩ or higher
      E40-2 (CANN) - D34-16 (BAT) Ignition switch off 6 kΩ or higher

    NG
    OK
  26. CONNECT CONNECTOR


    1. Reconnect the J76 No. 1 junction connector.


    NEXT
  27. CHECK FOR SHORT IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)


    1. A01CGV9E54
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      *b Front view of DLC3

      Disconnect the No. 2 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      J72-7 (CANH) - J72-18 (CANL) Ignition switch off 108 to 132 Ω
      J72-7 (CANH) - D34-4 (CG) Ignition switch off 200 Ω or higher
      J72-18 (CANL) - D34-4 (CG) Ignition switch off 200 Ω or higher
      J72-7 (CANH) - D34-16 (BAT) Ignition switch off 6 kΩ or higher
      J72-18 (CANL) - D34-16 (BAT) Ignition switch off 6 kΩ or higher

    NG
    OK
  28. CHECK FOR SHORT IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR SIDE)


    1. A01CHZVE04
      Text in Illustration
      *a

      Component with harness connected

      (Combination Meter Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      C19-14 (CANH) - C19-13 (CANL) Ignition switch off 108 to 132 Ω
      C19-14 (CANH) - C18-36 (SE) Ignition switch off 200 Ω or higher
      C19-13 (CANL) - C18-36 (SE) Ignition switch off 200 Ω or higher
      C19-14 (CANH) - C18-40 (B) Ignition switch off 6 kΩ or higher
      C19-13 (CANL) - C18-40 (B) Ignition switch off 6 kΩ or higher

    NG
    OK
  29. CONNECT CONNECTOR


    1. Reconnect the J72 No. 2 junction connector.


    NEXT
  30. CHECK FOR SHORT IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    1. A01CGV9E55
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      *b Front view of DLC3

      Disconnect the No. 3 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      J82-1 (CANH) - J82-12 (CANL) Ignition switch off 108 to 132 Ω
      J82-1 (CANH) - D34-4 (CG) Ignition switch off 200 Ω or higher
      J82-12 (CANL) - D34-4 (CG) Ignition switch off 200 Ω or higher
      J82-1 (CANH) - D34-16 (BAT) Ignition switch off 6 kΩ or higher
      J82-12 (CANL) - D34-16 (BAT) Ignition switch off 6 kΩ or higher

    NG
    OK
  31. CHECK FOR SHORT IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR SIDE)


    1. A01CHZVE04
      Text in Illustration
      *a

      Component with harness connected

      (Combination Meter Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      C19-14 (CANH) - C19-13 (CANL) Ignition switch off 108 to 132 Ω
      C19-14 (CANH) - C18-36 (SE) Ignition switch off 200 Ω or higher
      C19-13 (CANL) - C18-36 (SE) Ignition switch off 200 Ω or higher
      C19-14 (CANH) - C18-40 (B) Ignition switch off 6 kΩ or higher
      C19-13 (CANL) - C18-40 (B) Ignition switch off 6 kΩ or higher

    NG
    OK
  32. CONNECT CONNECTOR


    1. Reconnect the J82 No. 3 junction connector.


    NEXT
  33. CHECK FOR SHORT IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)


    1. A01CHO7E43
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 6 Junction Connector)

      *b Front view of DLC3

      Disconnect the No. 6 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      J58-3 (CANH) - J58-8 (CANL) Ignition switch off 108 to 132 Ω
      J58-3 (CANH) - D34-4 (CG) Ignition switch off 200 Ω or higher
      J58-8 (CANL) - D34-4 (CG) Ignition switch off 200 Ω or higher
      J58-3 (CANH) - D34-16 (BAT) Ignition switch off 6 kΩ or higher
      J58-8 (CANL) - D34-16 (BAT) Ignition switch off 6 kΩ or higher

    NG
    OK
  34. CHECK FOR SHORT IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR - SKID CONTROL ECU)


    1. A01CHO7E32
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 6 Junction Connector)

      *b Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      J58-4 (CANH) - J58-9 (CANL) Ignition switch off 200 Ω or higher
      J58-4 (CANH) - D34-4 (CG) Ignition switch off 200 Ω or higher
      J58-9 (CANL) - D34-4 (CG) Ignition switch off 200 Ω or higher
      J58-4 (CANH) - D34-16 (BAT) Ignition switch off 6 kΩ or higher
      J58-9 (CANL) - D34-16 (BAT) Ignition switch off 6 kΩ or higher

    NG
    OK
  35. CHECK FOR SHORT IN CAN BUS WIRE (NO. 6 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    1. A01CHO7E33
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 6 Junction Connector)

      *b Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      J58-5 (CANH) - J58-10 (CANL) Ignition switch off 108 to 132 Ω
      J58-5 (CANH) - D34-4 (CG) Ignition switch off 200 Ω or higher
      J58-10 (CANL) - D34-4 (CG) Ignition switch off 200 Ω or higher
      J58-5 (CANH) - D34-16 (BAT) Ignition switch off 6 kΩ or higher
      J58-10 (CANL) - D34-16 (BAT) Ignition switch off 6 kΩ or higher

    NG
    OK
  36. CONNECT CONNECTOR


    1. Reconnect the J58 No. 6 junction connector.


    NEXT
  37. CHECK FOR SHORT IN CAN BUS WIRE (SKID CONTROL ECU)


    1. A01CGLAE04
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Brake Actuator Assembly [Skid Control ECU])

      *b Front view of DLC3

      Disconnect the brake actuator assembly (skid control ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      B9-25 (CANH) - B9-14 (CANL) Ignition switch off 54 to 69 Ω
      B9-25 (CANH) - D34-4 (CG) Ignition switch off 200 Ω or higher
      B9-14 (CANL) - D34-4 (CG) Ignition switch off 200 Ω or higher
      B9-25 (CANH) - D34-16 (BAT) Ignition switch off 6 kΩ or higher
      B9-14 (CANL) - D34-16 (BAT) Ignition switch off 6 kΩ or higher

    NG
    OK
  38. CONNECT CONNECTOR


    1. Reconnect the J58 No. 6 junction connector.


    NEXT
  39. CHECK FOR SHORT IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)


    1. A01CJ10E04
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Combination Meter Assembly)

      *b Front view of DLC3

      Disconnect the combination meter assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      C19-14 (CANH) - C19-13 (CANL) Ignition switch off 108 to 132 Ω
      C19-14 (CANH) - D34-4 (CG) Ignition switch off 200 Ω or higher
      C19-13 (CANL) - D34-4 (CG) Ignition switch off 200 Ω or higher
      C19-14 (CANH) - D34-16 (BAT) Ignition switch off 6 kΩ or higher
      C19-13 (CANL) - D34-16 (BAT) Ignition switch off 6 kΩ or higher

    NG
    OK
  40. CHECK HARNESS AND CONNECTOR (ELECTRIC VEHICLE CONTROL ECU ASSEMBLY - BATTERY AND BODY GROUND)


    1. A01CIK4E04
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Electric Vehicle Control ECU Assembly)

      Connect the cable to the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. Disconnect the electric vehicle control ECU assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E43-5 (GND1) - Body ground Always Below 1 Ω
    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      E43-1 (AM1) - Body ground Always 20 to 28 V
      E43-2 (AM2) - Body ground Always 20 to 28 V
      E43-13 (ACC) - Body ground Ignition switch ACC 20 to 28 V

    NG
    OK