ENGINE IMMOBILISER SYSTEM, Diagnostic DTC:B2799

DTC Code DTC Name
B2799 Engine Immobiliser System Malfunction

DESCRIPTION

This DTC is stored when one of the following occurs: 1) the ECM detects errors in its own communications with the transponder key ECU assembly; 2) the ECM detects errors in the communication lines; or 3) the ECU - ECM communication ID between the transponder key ECU assembly and ECM is different and an engine start is attempted. Before troubleshooting for this DTC, make sure no engine immobiliser DTCs are output. If output, troubleshoot the engine immobiliser DTCs first.

DTC Code DTC Detection Condition Trouble Area DTC Enabling Condition
B2799

Either condition is met (1 trip detection logic*):


  • A malfunction occurs in the communication or communication lines between the ECM and transponder key ECU assembly.

  • A communication code cannot be verified during communication between the ECM and transponder key ECU assembly.


  • Harness or connector

  • Transponder key ECU assembly

  • ECM

Either condition is met:


  • 10 seconds after an engine start operation is performed (turn the ignition switch to ON). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

  • 10 seconds after the ignition switch is turned to ON after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the ignition switch being turned to ON, and DTCs are stored after 6 seconds).


WIRING DIAGRAM

A01CHKEE07

INSPECTION PROCEDURE

Note


  • When replacing the transponder key ECU assembly or ECM, refer to the Service Bulletin.

  • After performing repairs, perform the operation that fulfills the DTC enabling condition, and then confirm that no DTCs are output again.

PROCEDURE


  1. CLEAR DTC


    1. Clear the DTCs Click here.


    NEXT
  2. CHECK FOR DTC


    1. Check for DTCs Click here.

      OK
      DTC B2799 is not output.

    NG
    OK
  3. CHECK CONNECTION OF CONNECTOR


    1. Turn the ignition switch off.

    2. Check that the connectors are properly connected to the ECM and transponder key ECU.

      OK
      Connectors are properly connected.

    NG
    OK
  4. REREGISTER ECU - ECM COMMUNICATION ID


    1. Reregister the ECU - ECM communication ID (refer to the Service Bulletin).


    NEXT
  5. CLEAR DTC


    1. Clear the DTCs Click here.


    NEXT
  6. CHECK FOR DTC


    1. Check for DTCs Click here.

      OK
      DTC B2799 is not output.

    NG
    OK
  7. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)


    1. Disconnect the T18 transponder key ECU connector.

    2. Disconnect the E40 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T18-12 (EFII) - E40-15 (IMO) Always Below 1 Ω
      T18-13 (EFIO) - E40-9 (IMI) Always Below 1 Ω
      E40-15 (IMO) - Body ground Always 10 kΩ or higher
      E40-9 (IMI) - Body ground Always 10 kΩ or higher
    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      E40-15 (IMO) - Body ground Always Below 1 V
      E40-9 (IMI) - Body ground Always Below 1 V

    NG
    OK
  8. REPLACE ECM


    1. Replace the ECM Click here.

    2. Reregister the ECU - ECM communication ID (refer to the Service Bulletin).


    NEXT
  9. CLEAR DTC


    1. Clear the DTCs Click here.


    NEXT
  10. CHECK FOR DTC


    1. Check for DTCs Click here.

      OK
      DTC B2799 is not output.

    NG
    OK