STEERING PAD DISPOSAL

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


  1. PRECAUTION

    CAUTION:


    • An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

    • Never dispose of a steering pad with an undeployed airbag.

    • The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.

    • When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.

    • When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the steering pad.

    • The steering pad becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

    • Use gloves and safety glasses when handling a steering pad with a deployed airbag.

    • Do not apply water etc. to a steering pad with a deployed airbag.

    • Always wash your hands with water after completing the operation.

    Tech Tips

    When scrapping a vehicle equipped with an SRS or disposing of the steering pad, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs during the airbag deployment, contact the Service Dept. of the distributor.

  2. DISPOSE OF STEERING PAD (When Installed in Vehicle)

    Note


    • When disposing of the steering pad, never use the customer's vehicle to deploy the airbag.

    • Be sure to observe the following procedure when deploying the airbag.

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. A01CH7KE21

      Check the function of SST.

      SST
      09082-00700

      CAUTION:

      When deploying the airbag, always use the specified SST:

      SRS Airbag Deployment Tool


      1. A01CIM3E07
        Text in Illustration
        *1 Battery

        Connect SST to the battery.

        Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      2. A01CIR4E03

        Check the function of SST.

        Press SST activation switch and check that the LED of SST activation switch comes on.

        CAUTION:


        • Do not connect the yellow SST connector to the airbag.

        • If the LED comes on when the activation switch is not being pressed, SST is malfunctioning. Replace SST.

      3. Disconnect SST from the battery.

    2. Refer to Precaution Click here.

    3. Remove the lower steering column cover Click here.

    4. Remove the upper steering column cover Click here.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    6. Install SST.

      CAUTION:

      Check that there is no looseness in the steering wheel and steering pad.


      1. A01CGKPE02
        Text in Illustration
        *1 Lock Slider
        *2 Airbag Connector (Yellow Colored)

        Pull the lock slider in the direction indicated by the arrow to release the connector lock and disconnect the airbag connector (yellow colored) from the spiral cable sub-assembly.

        Note

        When handling the airbag connector, take care not to damage the airbag wire harness.

      2. A01CIF2E02
        Text in Illustration
        *1 Lock Slider
        *a Lock Position

        Connect SST connector to the airbag connector of the spiral cable sub-assembly.

        SST
        09082-00700

        Note

        To avoid damaging SST connector and the wire harness, do not lock the secondary lock of the twin lock.

      3. Check that the lock slider is in the lock position.

    7. Close all the doors.

    8. A01CH9VE02
      Text in Illustration
      *1 Battery
      *a 10 m or more

      Move SST at least 10 m (32.8 ft.) away from the vehicle front side window.

    9. Deploy the airbag.


      1. Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.

      2. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      3. Press SST activation switch to deploy the airbag.

        CAUTION:


        • Before deployment, make sure that no one is near the vehicle.

        • The steering pad becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

        • Use gloves and safety glasses when handling a steering pad with a deployed airbag.

        • Do not apply water etc. to a steering pad with a deployed airbag.

        • Always wash your hands with water after completing the operation.

        Tech Tips

        The airbag is deployed as the LED of SST activation switch comes on.

  3. DISPOSE OF STEERING PAD (When Not Installed in Vehicle)

    Note

    Be sure to follow the procedure detailed below when deploying the airbag.

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. A01CH7KE21

      Check the function of SST.

      SST
      09082-00700

      CAUTION:

      When deploying the airbag, always use the specified SST:

      SRS Airbag Deployment Tool


      1. A01CIM3E07
        Text in Illustration
        *1 Battery

        Connect SST to the battery.

        Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      2. A01CIR4E03

        Check the function of SST.

        Press SST activation switch and check that the LED of SST activation switch comes on.

        CAUTION:


        • Do not connect the yellow SST connector to the airbag.

        • If the LED comes on when the activation switch is not being pressed, SST is malfunctioning. Replace SST.

      3. Disconnect SST from the battery.

    2. Read the Precaution Click here.

    3. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    4. Remove the steering pad Click here.

      CAUTION:

      When storing the steering pad, keep the airbag deployment side facing upward.

    5. A01CIKFE45

      Using a service-purpose wire harness for the vehicle, tie the steering pad to a disc wheel.

      Text in Illustration
      *a Wire Harness Diameter
      *b Stripped Wire Harness Section
      Cross-sectional area of stripped wire harness section
      1.25 mm2 (0.0019 in.2) or more

      CAUTION:

      If the wire harness is too thin or an alternative object is used to tie down the steering pad, it may be snapped by the shock when the airbag is deployed. Always use a wire harness for vehicle use with a cross-sectional area of at least 1.25 mm2(0.0019 in.2).

      Tech Tips

      To calculate the area of the stripped wire section:

      Area = 3.14 x (Diameter)2/ 4


      1. A01CGYWE01

        Install 2 bolts with washers into the 2 bolt holes of the steering pad.

        Bolt
        L: 35.0 mm (1.38 in.)
        M: 6.0 mm (0.236 in.)
        Pitch: 1.0 mm (0.0394 in.)

        Note


        • Tighten the bolts by hand until they become difficult to turn.

        • Do not tighten the bolts excessively.

      2. A01CGUEE02
        Text in Illustration
        *a 2 times or more

        Wind 3 wire harnesses at least 2 times each around the bolts installed on the left and right sides of the steering pad.

        CAUTION:


        • Tightly wind the wire harnesses around the bolts so that there is no slack.

        • Make sure that the wire harnesses are tight. If there is slack in the wire harnesses, the steering pad may become loose due to the shock when the airbag is deployed.

      3. A01CHAAE02

        Connect SST connector.

        SST
        09082-00802   ( 09082-10801, 09082-40800 )
      4. Push in the lock plate to lock SST connector.

        Text in Illustration
        *1 Lock Plate
      5. A01CJ6CE02

        Face the airbag deployment side of the steering pad upward on top of an unneeded tire and wheel set. Separately tie the left and right sides of the steering pad to the wheel through the hub nut holes. Position SST connector so that it hangs downward through the hub hole of the wheel.

        CAUTION:


        • Make sure that the wire harnesses are tight. If there is slack in the wire harnesses, the steering pad may become loose due to the shock when the airbag is deployed.

        • Always tie the steering pad with the airbag deployment side facing upward.

        Note

        The tire and wheel may be damaged by the airbag deployment, so use an unneeded tire and wheel.

    6. A01CIOXE01

      Install SST.

      CAUTION:

      Place the disc wheel on level ground.


      1. Connect SST connector.

        SST
        09082-00700

        Note

        To avoid damaging SST connector and the wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for SST wire harness inside the disc wheel.

      2. A01CJ3IE02
        Text in Illustration
        *a 10 m or more

        Move SST at least 10 m (32.8 ft.) away from the steering pad tied to the disc wheel.

    7. Cover the steering pad with a cardboard box or tires.


      1. A01CGWTE02
        Text in Illustration
        *1 Weight

        Covering method using a cardboard box:

        Cover the steering pad with a cardboard box and place weights on the cardboard box in 4 places with a total weight of at least 190 N (19 kgf, 43 lbf).

        Cardboard box size
        Must exceed the following dimensions
        X
        460 mm (1.51 ft.)
        Y
        650 mm (2.13 ft.)

        Note


        • When dimension Y of the cardboard box exceeds the diameter of the tire with disc wheel which the steering pad is tied to, X should be the following size.

          X = 460 mm (1.51 ft.) + width of tire

        • If a cardboard box which is smaller than the specified size is used, the cardboard box will be damaged by the shock from the airbag deployment.

      2. A01CI7WE01
        A01CIWT

        Covering method using tires:

        Place at least 3 tires without disc wheels on the tire with disc wheel which the steering pad is tied to. Place another tire with disc wheel on the tires.

        Text in Illustration
        *1 Tire (3 or more)
        *a Inner Diameter
        *b Width
        Tire size
        Must exceed the following dimensions
        Width
        185 mm (7.28 in.)
        Inner diameter
        360 mm (1.18 ft.)

        CAUTION:

        Do not use tires with disc wheels except on the top and bottom.

        Note


        • As the tires may be damaged by the airbag deployment, use tires that you are planning to throw away.

        • Do not place SST connector under the tire because it could be damaged.

        Tie the tires together with 2 wire harnesses.

        CAUTION:

        Make sure that the wire harnesses are tight. Looseness in the wire harnesses results in the tires coming free due to the shock when the airbag is deployed.

    8. Deploy the airbag.


      1. A01CHIYE02
        Text in Illustration
        *A Using Cardboard Box
        *B Using Tires
        *1 Battery
        *2 Steering Pad
        *a 10 m or more

        Check that no one is within a 10 m (32.8 ft.) radius of the disc wheel which the steering pad is tied to.

      2. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      3. Press SST activation switch to deploy the airbag.

        CAUTION:

        When deploying the airbag, make sure that no one is near the tire.

        Tech Tips

        The airbag is deployed as the LED of SST activation switch comes on.

    9. Dispose of the steering pad.

      CAUTION:


      • The steering pad becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

      • Use gloves and safety glasses when handling a steering pad with a deployed airbag.

      • Do not apply water, etc. to a steering pad with a deployed airbag.

      • Always wash your hands with water after completing the operation.


      1. Remove the steering pad from the disc wheel.

      2. Place the steering pad in a plastic bag, tie it tightly and dispose of it in the same way as other general parts.