POWER STEERING GEAR REMOVAL


  1. REMOVE RADIATOR GRILLE


    1. A01CIXK

      Remove the 2 screws.

    2. A01CGV0E01

      Insert fingers into the grille as indicated by the arrows in the illustration to disengage the 2 clips.

    3. A01CIG1E01

      Insert fingers into the grille as indicated by arrows (A). Pull the radiator grille assembly straight to the front of the vehicle and disengage the 11 clips to remove the radiator grille assembly.

      Tech Tips

      When the clips cannot be disengaged, insert fingers into the grille as indicated by arrows (B) to remove the radiator grille assembly.

  2. REMOVE CLEARANCE LIGHT ASSEMBLY LH

    (See Pub. No. RM1008E, page 65-25)

  3. REMOVE HEADLIGHT ASSEMBLY LH

    (See Pub. No. RM1008E, page 65-12)

  4. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

  5. DRAIN POWER STEERING FLUID

  6. SEPARATE STEERING MAIN SHAFT ASSEMBLY


    1. A01CI8LE03

      Remove the bolt and slide the steering main shaft assembly.

      Note

      Do not separate the steering main shaft assembly from the power steering gear assembly.

    2. Put matchmarks on the steering main shaft assembly and the power steering gear assembly.

    3. Separate the steering main shaft assembly from the power steering gear assembly.

  7. DISCONNECT STEERING GEAR OUTLET RETURN TUBE


    1. A01CJESE04

      Using a union nut wrench, separate the steering gear outlet return tube from the power steering gear assembly.

  8. DISCONNECT PRESSURE FEED HOSE


    1. A01CH2HE04

      Using a union nut wrench, separate the pressure feed hose from the power steering gear assembly.

  9. SEPARATE STEERING DRAG LINK ASSEMBLY


    1. A01CI4AE01

      Remove the cotter pin and nut from the front of the steering drag link assembly.

    2. A01CIM4

      Install the nut upside down to the front of the steering drag link assembly.

      Tech Tips

      Install the nut upside down as shown in the illustration to prevent SST from damaging the stud bolt.

    3. A01CHLIE01

      Using SST, separate the drag link from the pitman arm.

      SST
      09610-20012
    4. Remove the nut.

  10. REMOVE PITMAN ARM


    1. A01CILO

      Remove the sector shaft to pitman arm setting hexagon nut and the spring washer.

    2. A01CGL6E02

      Put matchmarks on the sector shaft and pitman arm.

    3. A01CGM5E03

      Using SST, remove the pitman arm from the power steering gear assembly.

      SST
      09950-40011   ( 09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04031, 09958-04011 )

      Note


      • Apply a small amount of grease to the threads and tip of SST (center bolt) before use.

      • Be careful not to damage the sector shaft dust cover.

      Tech Tips

      If the pitman arm is firmly engaged with the power steering assembly, tap the pitman arm using a plastic hammer and brass bar.

  11. REMOVE POWER STEERING GEAR ASSEMBLY


    1. A01CIEXE01

      Remove the 2 bolts, 2 nuts, 2 washers and power steering gear assembly.

      Note

      Be careful not to drop the power steering gear assembly because it is extremely heavy.

  12. REMOVE STUD BOLT


    1. A01CGUGE08

      Install the 2 nuts to the stud bolt.

      Recommended service nut
      Thread diameter
      14.0 mm (0.551 in.)
      Thread pitch
      1.5 mm (0.059 in.)
    2. Lock the lower nut using the upper nut.

    3. A01CITLE01

      Turn the lower nut and remove the stud bolt.