EASY AND SMOOTH START SYSTEM, Diagnostic DTC:P0501/24

DTC Code DTC Name
P0501/24 Vehicle Speed Sensor "A" Range / Performance

DESCRIPTION

The skid control ECU (brake actuator assembly) receives the wheel speed pulse signals that are output by the anti-lock brake system speed sensors installed to each wheel, and inputs them as the vehicle speed signal to the combination meter assembly via a direct line. The vehicle speed signal that is input to the combination meter assembly is then input to the electric vehicle control ECU assembly via a direct line. At the same time, the electric vehicle control ECU assembly receives the wheel speed from the skid control ECU (brake actuator assembly) via CAN communication.

DTC No. Detection Condition Trouble Area
P0501/24
  • Injection volume and engine speed are more than a specified amount, the shift lever is not in N, and the vehicle is being driven with the clutch engaged, but the detected vehicle speed is 0 km/h.

  • Detected vehicle speed is 200 km/h or more.

  • Wheel speed received from the skid control ECU is 40 km/h or more, but the detected vehicle speed is 0 km/h.


  • Speed sensor circuit

  • Skid control ECU (brake actuator assembly)

  • Combination meter assembly

  • Harness or connector

  • Electric vehicle control ECU assembly

  • CAN communication line

WIRING DIAGRAM

A01CI64E01

INSPECTION PROCEDURE

Note


  • After replacing the electric vehicle control ECU assembly, perform clutch pedal stroke sensor assembly release position calibration Click here.

  • DTCs stored in the electric vehicle control ECU assembly are not cleared even after the system returns to a normal condition, so clear the DTCs after performing troubleshooting Click here.

PROCEDURE


  1. CHECK CAN COMMUNICATION SYSTEM


    1. Check if a CAN communication system DTC is output Click here

      Result
      Result Proceed to
      DTC is not output A
      DTC is output B

    B
    A
  2. CHECK COMBINATION METER ASSEMBLY


    1. Drive the vehicle.

    2. Check the speedometer in the combination meter assembly.

      OK
      The value indicated on the speedometer varies according to the driving speed.

      CAUTION:

      When performing the driving test, obey all speed limits and traffic laws.


    NG
    OK
  3. CHECK HARNESS AND CONNECTOR (ELECTRIC VEHICLE CONTROL ECU ASSEMBLY - COMBINATION METER ASSEMBLY)


    1. Turn the ignition switch off.

    2. Disconnect the E41 electric vehicle control ECU assembly connector.

    3. Disconnect the C18 combination meter assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E41-17 (SPD) - C18-23 (SP02) Always Below 1 Ω
      E41-17 (SPD) or C18-23 (SP02) - Body ground Always 10 kΩ or higher
    5. Reconnect the E41 electric vehicle control ECU assembly connector.

    6. Reconnect the C18 combination meter assembly connector.


    NG
    OK
  4. READ VALUE USING INTELLIGENT TESTER

    Tech Tips

    First, check that the speedometer operates correctly.


    1. Warm up the engine.

    2. Turn the ignition switch off.

    3. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    4. Connect the intelligent tester to the DLC3.

    5. Turn the ignition switch to ON.

    6. Turn the intelligent tester on.

    7. Enter the following menus: Powertrain / Vehicle Control / Data List.

    8. According to the display on the intelligent tester, read the Data List.

      Vehicle Control
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Vehicle Speed

      Vehicle speed/

      Min.: 0 km/h, Max.: 250 km/h

      Vehicle stopped: 0 km/h Input from combination meter assembly via direct line
    9. Drive the vehicle.

      OK
      The Data List display on the intelligent tester and the speedometer display are identical.

      CAUTION:

      When performing the driving test, obey all speed limits and traffic laws.


    NG
    OK
  5. CHECK ANTI-LOCK BRAKE SYSTEM


    1. Check if an anti-lock brake system DTC is output Click here

      Result
      Result Proceed to
      DTC is not output A
      DTC is output B

    B
    A