EASY AND SMOOTH START SYSTEM, Diagnostic DTC:C1382/112

DTC Code DTC Name
C1382/112 Clutch Stroke Sensor

DESCRIPTION

The clutch pedal stroke sensor detects the depressed volume of the pedal and sends the signal to the skid control ECU.

DTC Code DTC Detection Condition Trouble Area
C1382/112
  1. While accelerating from 0 km/h (0 mph) to 40 km/h (25 mph), the difference between the maximum and minimum output voltage of the clutch pedal stroke sensor drops to 1.96 V or less for 5 times consecutively.

  2. Output voltage of the clutch pedal stroke sensor is less than 3.2 V continuously for 1 second or more.

  3. Output voltage of the clutch pedal stroke sensor is 4.85 V or more or less than 0.15 V continuously for 1 second or more.


  • Open or short in wire harness

  • Improperly connected connector or corroded terminal

  • Clutch pedal stroke sensor

  • Skid control ECU

WIRING DIAGRAM

A01CGLIE01

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK CLUTCH PEDAL


    1. Check that the clutch pedal and the clutch pedal stroke sensor are properly installed and that the pedal can be operated normally.

    2. Check and adjust the clutch pedal height Click here.

    3. Adjust the clutch pedal stroke sensor.


    NEXT
  2. INSPECT CLUTCH PEDAL STROKE SENSOR


    1. A01CHAN

      Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    2. Remove the clutch pedal stroke sensor.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (C+B) - 3 (C-S) Always 16 to 24 kΩ
    4. A01CHLJ

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (C+B) - 2 (CSS) Sensor arm A position 0.32 to 0.48 kΩ
      Sensor arm B position 1.92 to 2.88 kΩ
    5. Move the sensor arm from A to B while inspecting the resistance between terminals 1 (+) and 2 (SIG).

      OK
      Resistance changes continuously.

    NG
    OK
  3. CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL STROKE SENSOR - SKID CONTROL ECU)


    1. Turn the ignition switch off.

    2. Disconnect the skid control ECU connector and clutch pedal stroke sensor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      S14-4 (CL+) - C10-1 (C+B) Always Below 1 Ω
      S14-4 (CL+) - Body ground Always 10 kΩ or higher
      S14-15 (CLS) - C10-2 (CSS) Always Below 1 Ω
      S14-15 (CLS) - Body ground Always 10 kΩ or higher
      S14-16 (CL-) - C10-3 (C-S) Always Below 1 Ω
      S14-16 (CL-) - Body ground Always 10 kΩ or higher

    NG
    OK
  4. RECONFIRM DTC


    1. Reconnect the skid control ECU connector and clutch pedal stroke sensor connector.

    2. Clear the DTCs Click here.

    3. Perform a road test.

    4. Check if the same DTC is recorded Click here.

      Result
      Result Proceed to
      DTC (C1382/112) is not output A
      DTC (C1382/112) is output B

    B
    A