ANTI-LOCK BRAKE SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Warm up the engine.

    2. Turn the ignition switch off.

    3. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    4. Connect the intelligent tester to the DLC3.

    5. Turn the ignition switch to the ON position.

    6. Turn on the intelligent tester.

    7. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    8. According to the display on the tester, perform the Data List.

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      ABS Motor Relay ABS motor relay / ON or OFF

      ON: Motor relay ON

      OFF: Motor relay OFF

      -
      Solenoid Relay Solenoid relay / ON or OFF

      ON: Solenoid relay ON

      OFF: Solenoid relay OFF

      -
      Stop Light SW Stop light switch / ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      -
      Parking Brake SW Parking brake switch / ON or OFF

      ON: Parking brake applied

      OFF: Parking brake released

      -
      FR Wheel ABS Control FR ABS operation / BEFORE or OPERATE

      BEFORE: No ABS operation

      OPERATE: During ABS operation

      -
      FL Wheel ABS Control FL ABS operation / BEFORE or OPERATE

      BEFORE: No ABS operation

      OPERATE: During ABS operation

      -
      RR Wheel ABS Control RR ABS operation / BEFORE or OPERATE

      BEFORE: No ABS operation

      OPERATE: During ABS operation

      -
      RL Wheel ABS Control RL ABS operation / BEFORE or OPERATE

      BEFORE: No ABS operation

      OPERATE: During ABS operation

      -
      FR Wheel Speed FR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer
      FL Wheel Speed FL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer
      RR Wheel Speed RR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer
      RL Wheel Speed RL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer
      ECU IG Power Voltage ECU IG power supply voltage / TOO LOW, NORMAL or TOO HIGH

      TOO LOW: Below 19 V

      NORMAL: 20 to 32 V

      TOO HIGH: 33 V or higher

      -
      Solenoid (SFRR) ABS solenoid (SFRR) / ON or OFF ON: Operates -
      Solenoid (SFRH) ABS solenoid (SFRH) / ON or OFF ON: Operates -
      Solenoid (SFLR) ABS solenoid (SFLR) / ON or OFF ON: Operates -
      Solenoid (SFLH) ABS solenoid (SFLH) / ON or OFF ON: Operates -
      Solenoid (SRRR) ABS solenoid (SRRR) / ON or OFF ON: Operates -
      Solenoid (SRRH) ABS solenoid (SRRH) / ON or OFF ON: Operates -
      Solenoid (SRLR) ABS solenoid (SRLR) / ON or OFF ON: Operates -
      Solenoid (SRLH) ABS solenoid (SRLH) / ON or OFF ON: Operates -
      Solenoid (SRMF) Master cut solenoid (SRM1) / ON or OFF ON: Operates -
      Solenoid (SRMR) Master cut solenoid (SRM2) / ON or OFF ON: Operates -
      Solenoid (SMF) Master cut solenoid (SMC1) / ON or OFF ON: Operates -
      Solenoid (SMR) Master cut solenoid (SMC2) / ON or OFF ON: Operates -
      Master Cylinder Sensor 1 Master cylinder pressure sensor 1 reading / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.7 V Reading increases when brake pedal is depressed
      Vacuum Sensor 1 Vacuum sensor 1 reading / min.: 0 V, max.: 5 V

      Min.: 0 V

      Max.: 5 V

      -
      Vacuum Sensor 2 Vacuum sensor 2 reading / min.: 0 V, max.: 5 V

      Min.: 0 V

      Max.: 5 V

      -
      Test Mode Test Mode operation / NORMAL or TEST

      NORMAL: Normal mode

      TEST: Test mode

      -
      Number of DTC Number of DTC recorded / min.: 0, max.: 255

      Min.: 0

      Max.: 255

      -
  2. ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Warm up the engine.

    2. Turn the ignition switch off.

    3. Replace the normal DLC3 cable (12 V specification) for the intelligent tester with the 24 V DLC3 cable.

      Note

      Be sure to use the 24 V DLC3 cable when connecting the intelligent tester to the DLC3. Using the normal DLC3 cable (12 V specification) will cause damage to the tester.

    4. Connect the intelligent tester to the DLC3.

    5. Turn the ignition switch to the ON position.

    6. Turn on the intelligent tester.

    7. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    8. According to the display on the tester, perform the Active Test.

      Tester Display Test Part Control Range Diagnostic Note
      ABS Solenoid (SFRR) ABS solenoid (SFRR) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SFRH) ABS solenoid (SFRH) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SFLR) ABS solenoid (SFLR) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SFLH) ABS solenoid (SFLH) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SRRR) ABS solenoid (SRRR) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SRRH) ABS solenoid (SRRH) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SRLR) ABS solenoid (SRLR) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard
      ABS Solenoid (SRLH) ABS solenoid (SRLH) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard
      TRC Solenoid (SRMF) Master cut solenoid (SRM1) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard
      TRC Solenoid (SRMR) Master cut solenoid (SRM2) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard
      TRC Solenoid (SMF) Master cut solenoid (SM1) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard
      TRC Solenoid (SMR) Master cut solenoid (SM2) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard
      Solenoid Relay ABS solenoid relay Relay ON / OFF Operating sound of motor can be heard
      ABS Motor Relay ABS motor relay Relay ON / OFF Operating sound of motor can be heard
      ABS Warning Light ABS warning light Warning light ON / OFF Observe combination meter
      Brake Warning Light Brake warning light Warning light ON / OFF Observe combination meter
      Exhaust Brake Cut Relay Exhaust brake cut relay Relay ON / OFF Operating sound of motor can be heard