HEADUP DISPLAY SYSTEM, Diagnostic DTC:B150A

DTC Code DTC Name
B150A Lost Communication with HMI-LAN

DESCRIPTION

The headup display (meter mirror sub-assembly) receives signals from the radio receiver assembly via local bus communication and displays audio system and navigation system information on the headup display.

This DTC is stored when the headup display (meter mirror sub-assembly) cannot receive the signal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B150A Lost Communication with HMI-LAN After the headup display (meter mirror sub-assembly) receives a registration information signal, which is sent by the radio receiver assembly when the engine switch is on (ACC), 1 or more times, the headup display (meter mirror sub-assembly) cannot receive the signal for 30 seconds or more.
  • Harness or connector

  • Radio receiver assembly

  • Headup display (Meter mirror sub-assembly)

DTC stored -

WIRING DIAGRAM


  1. w/ Navigation System

    B005PQTE69
    *1 Radio Receiver Assembly
    *2 Headup Display (Meter Mirror Sub-assembly)
    *3 Local Bus Communication Line
  2. w/ Audio and Visual System

    B005Q9DE03

PROCEDURE


  1. CONFIRM MODEL


    1. Choose the model to be inspected.

      Result
      Result Proceed to
      w/ Navigation System A
      w/ Audio and Visual System B

    B
    A
  2. CHECK FOR DTC


    1. Check if navigation system DTCs are output.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      Result
      Result Proceed to
      Navigation system DTCs are not output. A
      Navigation system DTCs are output. B

    B
    A
  3. CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - RADIO RECEIVER ASSEMBLY)


    1. Disconnect the K1 headup display (meter mirror sub-assembly) connector.

    2. Disconnect the J50 radio receiver assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K1-8 (TX-) - J50-21 (CNL2) Always Below 1 Ω
      K1-7 (TX+) - J50-20 (CNH2) Always Below 1 Ω
      K1-8 (TX-) or J50-21 (CNL2) - Body ground Always 10 kΩ or higher
      K1-7 (TX+) or J50-20 (CNH2) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG
    OK
  4. CHECK FOR DTC


    1. Check if meter / gauge system DTCs are output.

      Click here


      Body Electrical > Combination Meter > Trouble Codes
      Result
      Result Proceed to
      DTC B150A is not output. A
      DTC B150A is output. B

    A
    B
  5. CHECK FOR DTC


    1. Check if audio and visual system DTCs are output.

      for 8 Inch Display: Click here

      for 12.3 Inch Display: Click here


      Body Electrical > Navigation System > Trouble Codes
      Result
      Result Proceed to
      Audio and visual system DTCs are not output. A
      Audio and visual system DTCs are output. B

    B
    A
  6. CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - RADIO RECEIVER ASSEMBLY)


    1. Disconnect the K1 headup display (meter mirror sub-assembly) connector.

    2. Disconnect the J55*1 or J50*2 radio receiver assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K1-8 (TX-) - J55-4 (CNL1)*1 Always Below 1 Ω
      K1-7 (TX+) - J55-3 (CNH1)*1 Always Below 1 Ω
      K1-8 (TX-) or J55-4 (CNL1) - Body ground*1 Always 10 kΩ or higher
      K1-7 (TX+) or J55-3 (CNH1) - Body ground*1 Always 10 kΩ or higher
      K1-8 (TX-) - J50-21 (CNL2)*2 Always Below 1 Ω
      K1-7 (TX+) - J50-20 (CNH2)*2 Always Below 1 Ω
      K1-8 (TX-) or J50-21 (CNL2) - Body ground*2 Always 10 kΩ or higher
      K1-7 (TX+) or J50-20 (CNH2) - Body ground*2 Always 10 kΩ or higher

      • *1: for 8 Inch Display

      • *2: for 12.3 Inch Display

      Result
      Proceed to
      OK
      NG

    NG
    OK
  7. CHECK FOR DTC


    1. Check if meter / gauge system DTCs are output.

      Click here


      Body Electrical > Combination Meter > Trouble Codes
      Result
      Result Proceed to
      DTC B150A is not output. A
      DTC B150A is output. B

    A
    B