FUNCTION OF MAIN COMPONENTS
The blind spot monitor system has the following functions:
| Function | Outline | |
|---|---|---|
| Blind Spot Monitor Sensors LH and RH |
|
|
| Outer Rear View Mirror Assembly
|
|
|
| Headlight Dimmer Switch Assembly
|
Transmits the turn signal light switch signal to the blind spot monitor sensor LH and RH. | |
| Combination Meter Assembly | Multi-information Display
|
|
| Park/Neutral Position Switch Assembly*1 | Transmits the shift position signal to the ECM or TCM*2. | |
| Back-up Light Switch Assembly*3 | Transmits the on/off signals of the back-up light switch assembly to the ECM. | |
| Central Gateway ECU | Transmits the signal between the CAN communication bus. | |
| Steering Sensor | Transmits the steering angle signal to the blind spot monitor sensor LH and RH. | |
| Skid Control ECU | Transmits the vehicle speed signal to the blind spot monitor sensor LH and RH. | |
| Main Body ECU (Multiplex Network Body ECU) |
|
|
| ECM and TCM*2 | Transmits the reverse signal to the blind spot monitor sensor LH and RH. | |
| RCTA Buzzer (Blind Spot Monitor Buzzer)*4 | Sounds when a vehicle is detected in the alert area while backing up. | |
*1: Models with automatic transaxle or CVT
*2: Models with U660F automatic transaxle
*3: Models with manual transaxle
*4: Models with RCTA function
SYSTEM CONTROL
Operating Condition (Blind Spot Monitor Function)
The blind spot monitor function operates when both of the following conditions are met:
The blind spot monitor main switch is on.
The vehicle speed is greater than approximately 16 km/h (10 mph).
The blind spot monitor function can detect vehicles in its detection areas.
The detection areas formed by the blind spot monitor sensor LH and RH are as shown below:
| *a | 3.0 m (9.8 ft.) | *b | 1.0 m (3.3 ft.) |
| *c | 0.5 m (1.6 ft.) | - | - |
|
Detection Area | - | - |
When this vehicle is overtaken by another vehicle in the adjacent lane.
| *a | Another Vehicle | *b | This Vehicle |
|
Vehicle Speed (Fast) | |
Vehicle Speed (Slow) |
|
Detection Area | - | - |
When another vehicle enters the detection area of this vehicle due to a lane change.
| *a | Another Vehicle | *b | This Vehicle |
| *c | Another vehicle enters the detection area during lane change (merge in) (Type 1). | *d | Another vehicle enters the detection area during lane change (merge in) (Type 2). |
|
Motion Direction of Another Vehicle | |
Motion Direction of This Vehicle |
|
Detection Area | - | - |
Operating Condition (RCTA Function)
The RCTA function can detect vehicles in its detection areas.
The system continuously measures the relative speed of an approaching vehicle and its distance. If it is determined that the approaching vehicle will cross in the path of this vehicle, the Estimated Crossing Time (ECT) is calculated. When the ECT is 2.5 seconds or less, the system alerts the driver by flashing the outer rear view mirror indicator lights and sounding the RCTA buzzer.
| *a | This Vehicle | *b | Target Vehicle (Approximately 8 km/h (5 mph)) |
| *c | Target Vehicle (Approximately 28 km/h (18 mph)) | *d | Approximately 5.5 m (18.0 ft.) |
| *e | Approximately 20 m (65.6 ft.) | *f | Target Detection Line |
|
Alert Area | - | - |
Normal Parking
| *a | This Vehicle | *b | Target Vehicle |
|
Alert Area | - | - |
Angle Parking
| *a | This Vehicle | *b | Target Vehicle |
|
Alert Area | - | - |
FUNCTION
Blind Spot Monitor Function
According to operation conditions, the blind spot monitor function promotes safety confirmation by using the outer rear view mirror indicator light to inform the driver that another vehicle has entered the blind spot monitor sensor detection area of this vehicle.
The outer rear view mirror indicator light informs the driver that a vehicle is present in the blind spot detection area by illuminating when the turn signal light switch is not operated, and by flashing when a vehicle is present and the turn signal light switch is operated.
RCTA Function (Models with RCTA Function)
According to operation conditions, the RCTA function promotes safety confirmation by using the outer rear view mirror indicator lights and RCTA buzzer to inform the driver that another vehicle has entered the blind spot monitor sensor alert area of this vehicle.
When this vehicle is reversing, if a vehicle enters the alert area of the blind spot monitor sensors and it is determined the vehicle will cross in the path of this vehicle, the system alerts the driver by flashing the outer rear view mirror indicator lights and sounding the RCTA buzzer.
DIAGNOSIS
The blind spot monitor system is equipped with a diagnosis function that can display warning messages in the multi-information display. For details, refer to the Repair Manual.