RADIATOR REMOVAL
PROCEDURE
REMOVE HEADLIGHT ASSEMBLY LH
REMOVE HEADLIGHT ASSEMBLY RH
Tip:Use the same procedure as for the LH side.
REMOVE FRONT BUMPER ENERGY ABSORBER
REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY
REMOVE THERMISTOR ASSEMBLY
REMOVE NO. 1 ENGINE UNDER COVER
REMOVE BATTERY
REMOVE BATTERY CARRIER BRACKET SUB-ASSEMBLY
DRAIN ENGINE COOLANT
REMOVE INJECTOR DRIVER
REMOVE NO. 1 RADIATOR AIR GUIDE LH
Disengage the 2 claws and remove the clip and No. 1 radiator air guide LH.
REMOVE NO. 1 RADIATOR AIR GUIDE RH
-
Disengage the 2 claws and remove the clip and No. 1 radiator air guide RH.
-
REMOVE NO. 3 RADIATOR AIR GUIDE
-
Disengage the claw and remove the No. 3 radiator air guide.
-
REMOVE RADIATOR SUPPORT TO CROSS MEMBER BRACE SUB-ASSEMBLY
-
Disconnect the hone connector.
-
Remove the 2 bolts and radiator support to cross member brace sub-assembly.
-
REMOVE RADIATOR SUPPORT LH
-
Remove the bolt and radiator support LH.
Remove the radiator support cushion.
-
REMOVE RADIATOR SUPPORT RH
-
Remove the bolt and radiator support RH.
Remove the radiator support cushion.
-
REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY LH
-
Remove the 2 bolts and upper radiator support sub-assembly LH.
-
REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY RH
-
Remove the 2 bolts and upper radiator support sub-assembly RH.
-
DISCONNECT NO. 3 WATER BY-PASS HOSE
-
Disconnect the clamp.
Slide the clip and disconnect the No. 3 water by-pass hose.
-
DISCONNECT NO. 1 WATER HOSE CLAMP BRACKET
-
Remove the 2 bolts and 2 clamps and disconnect the No. 1 water hose clamp bracket from the upper radiator support sub-assembly.
-
REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY
-
Disconnect the hood lock control cable assembly from the hood lock control lever sub-assembly.
-
Disconnect the 2 clamps and hood lock control cable assembly from the upper radiator support sub-assembly.
-
Disconnect the engine hood courtesy switch connector.
-
Disconnect the 2 clamps and wire harness.
-
Remove the 4 bolts and upper radiator support sub-assembly.
-
DISCONNECT NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
-
Slide the clip and disconnect the No. 1 vacuum transmitting pipe sub-assembly.
-
REMOVE INTERCOOLER AIR HOSE
-
*a
Retainer
Loosen the clamp and disconnect the intercooler air hose from the No. 1 air tube.
Pull the retainer and remove the intercooler air hose from the intercooler assembly.
-
REMOVE NO. 3 AIR HOSE
-
Loosen the 2 hose clamps.
Remove the No. 3 air hose from the No. 2 air tube and diesel throttle body.
-
DISCONNECT NO. 3 RADIATOR HOSE
-
Slide the clip and disconnect the clamp and No. 3 radiator hose.
-
DISCONNECT NO. 2 RADIATOR HOSE
-
Slide the clip and disconnect the No. 2 radiator hose.
-
REMOVE RADIATOR ASSEMBLY
-
Disconnect the clamp.
Disconnect the intake air temperature sensor connector, No. 2 cooling fan motor connector and cooling fan motor connector.
-
Remove the radiator assembly with the fan shroud.
Note:For vehicles with the air conditioning system, do not apply excessive force to the condenser assembly or pipe when removing the radiator assembly.
Remove the 2 lower radiator supports.
-
REMOVE NO. 2 AIR TUBE
-
Disconnect the clamp.
Disconnect the intake air temperature sensor connector.
-
Loosen the hose clamp.
Remove the bolt and No. 2 air tube.
-
REMOVE NO. 2 RADIATOR HOSE
-
Slide the clip and remove the No. 2 radiator hose.
-
REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
-
Remove the 3 bolts.
Slide the clip and disconnect the hose.
Disconnect the clamp and then remove the No. 1 vacuum transmitting pipe sub-assembly.
-
REMOVE LOWER RADIATOR SUPPORT SUB-ASSEMBLY LH
REMOVE LOWER RADIATOR SUPPORT SUB-ASSEMBLY RH
REMOVE INTERCOOLER ASSEMBLY
REMOVE FAN SHROUD
-
Remove the 2 bolts and lift the fan shroud from the radiator assembly.
-