POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Driver Door Window Only) Power Windows do not Operate Using All Window Switch

DTC Code DTC Name
Power Windows do not Operate Using All Window Switch

DESCRIPTION

The power windows operate by using the power window regulator master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly (for LH door or RH door)*.

The power window regulator master switch assembly, power window regulator switch assembly and rear power window regulator switch assemblies (for LH door or RH door)* connect the same power supply and ground lines.

*: w/ Rear Power Window

WIRING DIAGRAM

B319622E01
B319623E01
B319623E02

CAUTION / NOTICE / HINT

Note:

Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE

  1. CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)

    1. Disconnect the H11*1 or G11*2 power window regulator master switch assembly connector.

      • *1: for LHD

      • *2: for RHD

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Standard Voltage

      Table 1. for LHD with Rear Power Window

      Tester Connection

      Condition

      Specified Condition

      H11-6 (B) - Body ground

      Ignition switch ON

      11 to 14 V

      Table 2. for LHD without Rear Power Window

      Tester Connection

      Condition

      Specified Condition

      H11-15 (B) - Body ground

      Ignition switch ON

      11 to 14 V

      Table 3. for RHD with Rear Power Window

      Tester Connection

      Condition

      Specified Condition

      G11-6 (B) - Body ground

      Ignition switch ON

      11 to 14 V

      Table 4. for RHD without Rear Power Window

      Tester Connection

      Condition

      Specified Condition

      G11-15 (B) - Body ground

      Ignition switch ON

      11 to 14 V

      Standard Resistance

      Table 5. for LHD with Rear Power Window

      Tester Connection

      Condition

      Specified Condition

      H11-1 (E) - Body ground

      Always

      Below 1 Ω

      Table 6. for LHD without Rear Power Window

      Tester Connection

      Condition

      Specified Condition

      H11-7 (E) - Body ground

      Always

      Below 1 Ω

      Table 7. for RHD with Rear Power Window

      Tester Connection

      Condition

      Specified Condition

      G11-9 (E) - Body ground

      Always

      Below 1 Ω

      Table 8. for RHD without Rear Power Window

      Tester Connection

      Condition

      Specified Condition

      G11-7 (E) - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  2. REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

    1. Replace the power window regulator master switch assembly.

      Click hereClick here

    Result

    Proceed to

    NEXT

    NEXT
  3. CHECK POWER WINDOW CONTROL SYSTEM

    1. Check the operation of the power windows by using the power window regulator master switch assembly, power window regulator switch assembly and rear power window regulator switch assemblies (for LH door or RH door)*.

      *: w/ Rear Power Window

      Click here

      OK

      All power windows operate normally.

    Result

    Proceed to

    OK

    NG

    OK

    END (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)