NAVIGATION SYSTEM Speaker Circuit

DTC Code DTC Name
Speaker Circuit

DESCRIPTION

  • for 6 Speakers:

  • If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.

    Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly, telematics transceiver* or speakers.

  • for 9 Speakers:

  • If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.

    Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.

  • *: w/ Manual (SOS) Switch

WIRING DIAGRAM

  1. for 6 Speakers

    E348132E04
  2. for 9 Speakers

    E265409E01
    E265410E04

PROCEDURE

  1. CONFIRM MODEL

    1. Choose the model to be inspected.

      Result

      Result

      Proceed to

      for 6 Speakers

      A

      for 9 Speakers

      B

    B

    CHECK SPEAKER (OPERATION CHECK)Click here

    A
  2. CHECK SPEAKER (OPERATION CHECK)

    1. E268474

      Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

      Click here

    2. Perform the operation check above and determine the speaker that is not operating.

      Result

      Not Operating Speaker

      Proceed to

      Front No. 1 speaker assembly or front No. 2 speaker assembly

      (w/o Manual (SOS) Switch)

      A

      Front No. 1 speaker assembly or front No. 2 speaker assembly

      (w/ Manual (SOS) Switch)

      B

      Rear speaker assembly

      C

      Tip:

      If sound cannot be heard from any speaker, inspect all of them.

    B

    CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)Click here

    C

    CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)Click here

    A
  3. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)

    1. Disconnect the E1 radio and display receiver assembly connector.

    2. Disconnect the G1 and H1 front No. 1 speaker assembly connectors.

    3. Disconnect the G4 and H5 front No. 2 speaker assembly connectors.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E1-1 (FR+) - G4-4 (TWR+)

      Always

      Below 1 Ω

      E1-5 (FR-) - G4-2 (TWR-)

      Always

      Below 1 Ω

      E1-2 (FL+) - H5-4 (TWL+)

      Always

      Below 1 Ω

      E1-6 (FL-) - H5-2 (TWL-)

      Always

      Below 1 Ω

      G1-1 - G4-3 (+)

      Always

      Below 1 Ω

      G1-2 - G4-1 (-)

      Always

      Below 1 Ω

      H1-1 - H5-3 (+)

      Always

      Below 1 Ω

      H1-2 - H5-1 (-)

      Always

      Below 1 Ω

      E1-1 (FR+) or G4-4 (TWR+) - Body ground

      Always

      10 kΩ or higher

      E1-5 (FR-) or G4-2 (TWR-) - Body ground

      Always

      10 kΩ or higher

      E1-2 (FL+) or H5-4 (TWL+) - Body ground

      Always

      10 kΩ or higher

      E1-6 (FL-) or H5-2 (TWL-) - Body ground

      Always

      10 kΩ or higher

      G1-1 or G4-3 (+) - Body ground

      Always

      10 kΩ or higher

      G1-2 or G4-1 (-) - Body ground

      Always

      10 kΩ or higher

      H1-1 or H5-3 (+) - Body ground

      Always

      10 kΩ or higher

      H1-2 or H5-1 (-) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  4. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

    1. Remove the front No. 1 speaker assembly.

      for Sedan:Click here

      for Hatchback, Wagon:Click here

    2. E219303C30

      *a

      Component without harness connected

      (Front No. 1 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      1 - 2

      Always

      3.2 to 4.8 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

    for Sedan:Click here

    for Hatchback, Wagon:Click here

    OK
  5. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

    1. Remove the front No. 2 speaker assembly.

      for Sedan:Click here

      for Hatchback, Wagon:Click here

    2. E226097C11

      *A

      for RH

      *B

      for LH

      *a

      Component without harness connected

      (Front No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance (for RH)

      Tester Connection

      Condition

      Specified Condition

      4 (TWR+) - 2 (TWR-)

      Always

      10 kΩ or higher

      3 (+) - 4 (TWR+)

      Always

      Below 1 Ω

      1 (-) - 2 (TWR-)

      Always

      Below 1 Ω

      Standard Resistance (for LH)

      Tester Connection

      Condition

      Specified Condition

      4 (TWL+) - 2 (TWL-)

      Always

      10 kΩ or higher

      3 (+) - 4 (TWL+)

      Always

      Below 1 Ω

      1 (-) - 2 (TWL-)

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

    for Sedan:Click here

    for Hatchback, Wagon:Click here

    OK
  6. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

    1. Check that the malfunction disappears when a known good speaker is installed.

      for Sedan:Click here

      for Hatchback, Wagon:Click here

      OK

      Malfunction disappears.

      Tip:
      • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both the LH and RH side.

    Result

    Proceed to

    OK

    NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

  7. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)

    1. Disconnect the E1 radio and display receiver assembly connector.

    2. Disconnect the E143 telematics transceiver connector.

    3. Disconnect the G4 and H5 front No. 2 speaker assembly connectors.

    4. Disconnect the G1 and H1 front No. 1 speaker assembly connectors.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E1-1 (FR+) - E143-2 (SPI+)

      Always

      Below 1 Ω

      E1-5 (FR-) - E143-3 (SPI-)

      Always

      Below 1 Ω

      G4-4 (TWR+) - E143-5 (SPO+)

      Always

      Below 1 Ω

      G4-2 (TWR-) - E143-6 (SPO-)

      Always

      Below 1 Ω

      E1-2 (FL+) - H5-4 (TWL+)

      Always

      Below 1 Ω

      E1-6 (FL-) - H5-2 (TWL-)

      Always

      Below 1 Ω

      G4-3 (+) - G1-1

      Always

      Below 1 Ω

      G4-1 (-) - G1-2

      Always

      Below 1 Ω

      H5-3 (+) - H1-1

      Always

      Below 1 Ω

      H5-1 (-) - H1-2

      Always

      Below 1 Ω

      E1-1 (FR+) or E143-2 (SPI+) - Body ground

      Always

      10 kΩ or higher

      E1-5 (FR-) or E143-3 (SPI-) - Body ground

      Always

      10 kΩ or higher

      E1-2 (FL+) or H5-4 (TWL+) - Body ground

      Always

      10 kΩ or higher

      E1-6 (FL-) or H5-2 (TWL-) - Body ground

      Always

      10 kΩ or higher

      G4-4 (TWR+) or E143-5 (SPO+) - Body ground

      Always

      10 kΩ or higher

      G4-2 (TWR-) or E143-6 (SPO-) - Body ground

      Always

      10 kΩ or higher

      G4-3 (+) or G1-1 - Body ground

      Always

      10 kΩ or higher

      G4-1 (-) or G1-2 - Body ground

      Always

      10 kΩ or higher

      H5-3 (+) or H1-1 - Body ground

      Always

      10 kΩ or higher

      H5-1 (-) or H1-2 - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  8. INSPECT TELEMATICS TRANSCEIVER

    1. Remove the telematics transceiver.

      Click here

    2. E169849C05

      *a

      Component without harness connected

      (Telematics Transceiver)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      2 (SPI+) - 5 (SPO+)

      Always

      Below 1 Ω

      3 (SPI-) - 6 (SPO-)

      Always

      Below 1 Ω

      2 (SPI+) - 3 (SPI-)

      Always

      10 kΩ or higher

      5 (SPO+) - 6 (SPO-)

      Always

      10 kΩ or higher

      2 (SPI+) or 5 (SPO+) - Body ground

      Always

      10 kΩ or higher

      3 (SPI-) or 6 (SPO-) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE TELEMATICS TRANSCEIVER

    OK
  9. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

    1. Remove the front No. 1 speaker assembly.

      Click here

    2. E219303C30

      *a

      Component without harness connected

      (Front No. 1 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      1 - 2

      Always

      3.2 to 4.8 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

    OK
  10. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

    1. Remove the front No. 2 speaker assembly.

      Click here

    2. E226097C11

      *A

      for RH

      *B

      for LH

      *a

      Component without harness connected

      (Front No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      4 (TWR+) - 2 (TWR-)

      Always

      10 kΩ or higher

      3 (+) - 4 (TWR+)

      Always

      Below 1 Ω

      1 (-) - 2 (TWR-)

      Always

      Below 1 Ω

      4 (TWL+) - 2 (TWL-)

      Always

      10 kΩ or higher

      3 (+) - 4 (TWL+)

      Always

      Below 1 Ω

      1 (-) - 2 (TWL-)

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

    OK
  11. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

    1. Check that the malfunction disappears when a known good speaker is installed.

      Click here

      OK

      Malfunction disappears.

      Tip:
      • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both LH and RH sides.

    Result

    Proceed to

    OK

    NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

  12. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)

    1. Disconnect the E2 radio and display receiver assembly connector.

    2. Disconnect the L79 and L80 rear speaker assembly connectors (for Sedan).

      Disconnect the J2 and K2 rear speaker assembly connectors (for Hatchback, Wagon).

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (for Sedan)

      Tester Connection

      Condition

      Specified Condition

      E2-1 (RR+) - L79-1

      Always

      Below 1 Ω

      E2-3 (RR-) - L79-2

      Always

      Below 1 Ω

      E2-2 (RL+) - L80-1

      Always

      Below 1 Ω

      E2-6 (RL-) - L80-2

      Always

      Below 1 Ω

      E2-1 (RR+) or L79-1 - Body ground

      Always

      10 kΩ or higher

      E2-3 (RR-) or L79-2 - Body ground

      Always

      10 kΩ or higher

      E2-2 (RL+) or L80-1 - Body ground

      Always

      10 kΩ or higher

      E2-6 (RL-) or L80-2 - Body ground

      Always

      10 kΩ or higher

      Standard Resistance (for Hatchback, Wagon)

      Tester Connection

      Condition

      Specified Condition

      E2-1 (RR+) - J2-1

      Always

      Below 1 Ω

      E2-3 (RR-) - J2-2

      Always

      Below 1 Ω

      E2-2 (RL+) - K2-1

      Always

      Below 1 Ω

      E2-6 (RL-) - K2-2

      Always

      Below 1 Ω

      E2-1 (RR+) or J2-1 - Body ground

      Always

      10 kΩ or higher

      E2-3 (RR-) or J2-2 - Body ground

      Always

      10 kΩ or higher

      E2-2 (RL+) or K2-1 - Body ground

      Always

      10 kΩ or higher

      E2-6 (RL-) or K2-2 - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  13. INSPECT REAR SPEAKER ASSEMBLY

    1. Remove the rear speaker assembly.

      for Sedan:Click here

      for Hatchback, Wagon:Click here

    2. E219303C30

      *a

      Component without harness connected

      (Rear Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      1 - 2

      Always

      3.2 to 4.8 Ω

    Result

    Proceed to

    OK

    NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

    NG

    REPLACE REAR SPEAKER ASSEMBLY

    for Sedan:Click here

    for Hatchback, Wagon:Click here

  14. CHECK SPEAKER (OPERATION CHECK)

    1. E268474

      Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

      Click here

    2. Perform the operation check above and determine the speaker that is not operating.

      Result

      Not Operating Speaker

      Proceed to

      Front No. 1 speaker assembly

      A

      Front No. 2 speaker assembly

      B

      Rear speaker assembly

      C

      No. 1 speaker with box assembly

      D

      Tip:

      If sound cannot be heard from any speaker, inspect all of them.

    B

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)Click here

    C

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY)Click here

    D

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - NO. 1 SPEAKER WITH BOX ASSEMBLY)Click here

    A
  15. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)

    1. Disconnect the E91 stereo component amplifier assembly connector.

    2. Disconnect the G1 and H1 front No. 1 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E91-15 (FR+) - G1-1

      Always

      Below 1 Ω

      E91-30 (FR-) - G1-2

      Always

      Below 1 Ω

      E91-12 (FL+) - H1-1

      Always

      Below 1 Ω

      E91-27 (FL-) - H1-2

      Always

      Below 1 Ω

      E91-15 (FR+) or G1-1 - Body ground

      Always

      10 kΩ or higher

      E91-30 (FR-) or G1-2 - Body ground

      Always

      10 kΩ or higher

      E91-12 (FL+) or H1-1 - Body ground

      Always

      10 kΩ or higher

      E91-27 (FL-) or H1-2 - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  16. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

    1. Remove the front No. 1 speaker assembly.

      Click here

    2. E219303C30

      *a

      Component without harness connected

      (Front No. 1 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      1 - 2

      Always

      3.2 to 5.2 Ω

    Result

    Proceed to

    OK

    NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

  17. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)

    1. Disconnect the E91 stereo component amplifier assembly connector.

    2. Disconnect the G4 and H5 front No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E91-13 (TWR+) - G4-4

      Always

      Below 1 Ω

      E91-28 (TWR-) - G4-2

      Always

      Below 1 Ω

      E91-14 (TWL+) - H5-4

      Always

      Below 1 Ω

      E91-29 (TWL-) - H5-2

      Always

      Below 1 Ω

      E91-13 (TWR+) or G4-4 - Body ground

      Always

      10 kΩ or higher

      E91-28 (TWR-) or G4-2 - Body ground

      Always

      10 kΩ or higher

      E91-14 (TWL+) or H5-4 - Body ground

      Always

      10 kΩ or higher

      E91-29 (TWL-) or H5-2 - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  18. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

    1. Remove the front No. 2 speaker assembly.

      Click here

    2. E226097C12

      *a

      Component without harness connected

      (Front No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      4 - 2

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

    OK
  19. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

    1. Check that the malfunction disappears when a known good speaker is installed.

      Click here

      OK

      Malfunction disappears.

      Tip:
      • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left speaker is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both the LH and RH side.

    Result

    Proceed to

    OK

    NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

  20. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY)

    1. Disconnect the E91 stereo component amplifier assembly connector.

    2. Disconnect the J2 and K2 rear speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E91-11 (RR+) - J2-1 (+)

      Always

      Below 1 Ω

      E91-26 (RR-) - J2-2 (-)

      Always

      Below 1 Ω

      E91-10 (RL+) - K2-1 (+)

      Always

      Below 1 Ω

      E91-25 (RL-) - K2-2 (-)

      Always

      Below 1 Ω

      E91-11 (RR+) or J2-1 (+) - Body ground

      Always

      10 kΩ or higher

      E91-26 (RR-) or J2-2 (-) - Body ground

      Always

      10 kΩ or higher

      E91-10 (RL+) or K2-1 (+) - Body ground

      Always

      10 kΩ or higher

      E91-25 (RL-) or K2-2 (-) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  21. INSPECT REAR SPEAKER ASSEMBLY

    1. Remove the rear speaker assembly.

      Click here

    2. E219303C69

      *a

      Component without harness connected

      (Rear Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      1 (+) - 2 (-)

      Always

      3.6 to 4.4 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE REAR SPEAKER ASSEMBLY

    OK
  22. REPLACE REAR SPEAKER ASSEMBLY

    1. Check that the malfunction disappears when a known good speaker is installed.

      Click here

      OK

      Malfunction disappears.

      Tip:
      • Connect all the connectors to the rear speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left speaker is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both the LH and RH side.

    Result

    Proceed to

    OK

    NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

  23. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - NO. 1 SPEAKER WITH BOX ASSEMBLY)

    1. Disconnect the E91 stereo component amplifier assembly connector.

    2. Disconnect the L44 No. 1 speaker with box assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E91-9 (WFR+) - L44-1 (WF+)

      Always

      Below 1 Ω

      E91-24 (WFR-) - L44-3 (WF-)

      Always

      Below 1 Ω

      E91-8 (WFL+) - L44-4 (WF+)

      Always

      Below 1 Ω

      E91-23 (WFL-) - L44-2 (WF-)

      Always

      Below 1 Ω

      E91-9 (WFR+) or L44-1 (WF+) - Body ground

      Always

      10 kΩ or higher

      E91-24 (WFR-) or L44-3 (WF-) - Body ground

      Always

      10 kΩ or higher

      E91-8 (WFL+) or L44-4 (WF+) - Body ground

      Always

      10 kΩ or higher

      E91-23 (WFL-) or L44-2 (WF-) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  24. INSPECT NO. 1 SPEAKER WITH BOX ASSEMBLY

    1. Remove the No. 1 speaker with box assembly.

      for Wagon:Click here

      for Hatchback:Click here

    2. E219304C17

      *a

      Component without harness connected

      (No. 1 Speaker with Box Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      1 (WF+) - 3 (WF-)

      Always

      4.0 to 6.4 Ω

      2 (WF-) - 4 (WF+)

      Always

      4.0 to 6.4 Ω

    Result

    Proceed to

    OK

    NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

    NG

    REPLACE NO. 1 SPEAKER WITH BOX ASSEMBLY

    for Wagon:Click here

    for Hatchback:Click here