ANTI-LOCK BRAKE SYSTEM(for Type B), Diagnostic DTC:C146C and C146D

DTC Code DTC Name
C146C Open in ABS Motor Relay Circuit
C146D Short in ABS Motor Relay Circuit

DESCRIPTION

The ABS motor relay supplies power to the pump motor. While the ABS is activated, the ECU turns the motor relay on and operates the pump motor.

If the voltage supplied to the motor relay (+BM) is below the DTC detection threshold due to low voltage from the battery or alternator, these DTCs may be stored.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C146C

Open in ABS Motor Relay Circuit

Either of the following conditions is detected:

  1. All of the following conditions continue for 0.12 seconds or more.

    • The IG1 terminal voltage is 9.5 V or more.

    • Initial check is being performed, or ABS is operating.

    • Relay contact remains open when the relay is turned on.

  2. Both of the following conditions continue for 0.12 seconds or more.

    • The IG1 terminal voltage is less than 9.5 V.

    • Relay contact remains open when the relay is turned on.

  • ABS NO. 1 fuse

  • ABS motor relay circuit

  • Skid control ECU (Brake actuator assembly)

C146D

Short in ABS Motor Relay Circuit

When the motor relay is turned off, the motor relay remains closed for 4 seconds or more.

Skid control ECU (Brake actuator assembly)

Tip:

for C146C: Even after the trouble areas are repaired, the ABS warning light will not go off unless the following operations are performed.

  1. Drive the vehicle at 20 km/h (12 mph) for 30 seconds or more and check that the ABS warning light goes off.

  2. Clear the DTCs.

WIRING DIAGRAM

C278167E05

CAUTION / NOTICE / HINT

Note:

Inspect the fuses for circuits related to this system before performing the following procedure.

Tip:

When C1241 and/or C1417 is output together with C146C and/or C146D, inspect and repair the trouble areas indicated by C1241 and/or C1417 first.

for C1241:Click here

for C1417:Click here

PROCEDURE

  1. INSPECT HARNESS AND CONNECTOR (+BM TERMINAL)

    1. C277404C11

      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Actuator Assembly))

      Make sure that there is no looseness at the locking part and the connecting part of the connector.

    2. Disconnect the A124 skid control ECU (brake actuator assembly) connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      A124-24 (+BM) - Body ground

      Always

      11 to 14 V

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (+BM CIRCUIT)

    OK
  2. CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

    1. C277404C10

      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Actuator Assembly))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      A124-13 (GND2) - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)

    OK
  3. RECONFIRM DTC

    Tip:

    These DTCs are stored when a problem is identified in the skid control ECU (brake actuator assembly).

    The ABS motor relay is in the skid control ECU (brake actuator assembly).

    Therefore, motor relay inspection and motor relay unit inspection cannot be performed. Be sure to check if any DTCs are output again before replacing the skid control ECU (brake actuator assembly).

    1. Reconnect the A124 skid control ECU (brake actuator assembly) connector.

    2. Turn the ignition switch off.

    3. Clear the DTCs.

      Click here

      Chassis > ABS/VSC/TRC > Clear DTCs

    4. Turn the ignition switch off.

    5. Start the engine.

    6. Perform a road test.

    7. Check if the same DTC is output.

      Click here

      Chassis > ABS/VSC/TRC > Trouble Codes

      Result

      Result

      Proceed to

      DTCs C146C and C146D are not output.

      A

      DTCs C146C and/or C146D are output.

      B

      Tip:
      • If a speed signal of 6 km/h (4 mph) or more is sent to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

      • If the normal system code is output (No trouble codes are output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly).

      • If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

      • If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.

    A

    USE SIMULATION METHOD TO CHECK

    B

    REPLACE BRAKE ACTUATOR ASSEMBLY