SFI SYSTEM, Diagnostic DTC:P0336
| DTC Code | DTC Name |
|---|---|
| P0336 | Crankshaft Position Sensor "A" Circuit Range / Performance |
DESCRIPTION
The crankshaft position sensor monitors the stop position and performs start control from the position of the stopped crankshaft. Moreover, the crankshaft position sensor contains a function which detects reverse rotation to correctly detect the stop position when the engine rotates reversely.
When a malfunction occurs in the reverse rotation detection function, stop and start system is disabled.
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
|---|---|---|---|---|---|
P0336 |
Crankshaft Position Sensor "A" Circuit Range / Performance |
When one of the following conditions is met (1 trip detection logic):
|
|
Comes on |
DTC stored |
MONITOR DESCRIPTION
When one of the following malfunctions is detected, P0336 is output.
In case an engine reverse signal is detected for 4 seconds during engine cranking or normally rotating at 400 rpm or higher.
In case the pulse width of the crankshaft position sensor exceeding the threshold is detected for 4 seconds during engine normal rotation at 400 rpm or higher.
In case the input signal voltage of the crankshaft position sensor continues at 5 V for 4 seconds during engine rotation.
CONFIRMATION DRIVING PATTERN
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Idle the engine for 20 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
Tip:If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0336.
Check the DTC judgment result.
GTS Display
Description
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
Tip:If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
WIRING DIAGRAM
Refer to DTC P0335.
CAUTION / NOTICE / HINT
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0336)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
Powertrain > Engine and ECT > Trouble Codes
Result
Result
Proceed to
DTC P0336 and P0338 are output
A
DTC P0336 is output
B
B REPLACE CRANKSHAFT POSITION SENSORClick here
CHECK TERMINAL VOLTAGE (POWER SOURCE OF CRANKSHAFT POSITION SENSOR)
Result
Proceed to
OK
NG
NG CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)Click here
CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
Result
Proceed to
OK
NG
NG REPAIR OR REPLACE HARNESS OR CONNECTOR
CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
Result
Proceed to
OK
NG
INSPECT CRANKSHAFT (CRANKSHAFT ANGLE SENSOR PLATE)
Result
Proceed to
OK
NG
REPLACE CRANKSHAFT POSITION SENSOR
Result
Proceed to
NEXT
CHECK WHETHER DTC OUTPUT RECURS
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Powertrain > Engine and ECT > Clear DTCs
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
Powertrain > Engine and ECT > Trouble Codes
Result
Result
Proceed to
DTC is not output
A
DTC P0336 is output
B
A END
CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
Result
Proceed to
OK
NG
NG REPAIR OR REPLACE HARNESS OR CONNECTOR