CYLINDER BLOCK(w/o Glow Plug Controller) REASSEMBLY

PROCEDURE

  1. INSTALL OIL JET

    1. Tap in a new oil jet with the tip of the oil jet aligned with the cylinder block sub-assembly alignment mark.

      A286936C02

      *1

      Oil Jet

      -

      -

      *a

      Alignment Mark

      -

      -

      Note:

      Do not tap the tip of the oil jet.

  2. INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

    1. A198451

      Using a 5 mm hexagon socket wrench, install the 4 No. 1 oil nozzle sub-assemblies with the 4 bolts.

      9.0 N*m

      92 kgf*cm

      80 in.*lbf

  3. INSTALL CRANKSHAFT

    A299930C01

    *a

    No. 1 Journal Crankshaft Bearing

    *b

    No. 5 Journal Crankshaft Bearing

    Note:

    The types of No. 1 journal crankshaft bearing and No. 5 journal crankshaft bearing to be used for vehicles w/ Stop And Start System and w/o Stop And Start System are different. Use the correct parts for the vehicle specifications when replacing the crankshaft bearings.

    1. Install the crankshaft bearing with the oil groove to the cylinder block sub-assembly and the crankshaft bearing to the crankshaft bearing cap.

      A198454C06

      *a

      Cylinder Block Sub-assembly Side

      *b

      Crankshaft Bearing Cap Side

      *c

      Oil Groove

      -

      -

      Note:

      Do not apply engine oil to the contact surface of the cylinder block sub-assembly or the back side of the crankshaft bearings.

      Tip:

      Mass production parts do not have identification marks. If reusing a mass production part, measure the clearance of both sides so that the crankshaft bearing is in the center of the crankshaft bearing cap.

      Specified clearance

      A - B = 0.8 mm (0.0315 in.) or less

    2. A286937C02

      *a

      Oil Groove

      Install the 2 upper crankshaft thrust washers onto the cylinder block sub-assembly and the front and back side of the No. 3 journal with the oil groove facing outward.

    3. Apply engine oil to the crankshaft bearings, and then install the crankshaft onto the cylinder block sub-assembly.

    4. A198455C01
      V100135

      Engine Front Side

      Examine the front marks and numbers and check that the order is as shown in the illustration. Then, install the crankshaft bearing caps to the cylinder block sub-assembly.

    5. Apply a light coat of engine oil to the threads and contact surfaces of the 10 crankshaft bearing cap set bolts.

    6. A286934E01

      Temporarily tighten the 10 crankshaft bearing cap set bolts in several steps in the order shown in the illustration, and tighten them to the specified torque (*1).

      60 N*m

      612 kgf*cm

      44 ft.*lbf

      Tip:

      Check that the crankshaft turns smoothly while tightening the 10 crankshaft bearing cap set bolts.

    7. A286927C08

      *a

      Paint Mark

      V100136

      Engine Front

      Mark the front of the 10 crankshaft bearing cap set bolts with paint.

    8. Tighten the 10 crankshaft bearing cap set bolts by 90° in the same order as in step (*1).

    9. Check that each paint mark is now at a 90° angle to the front.

  4. INSTALL WITH PIN PISTON SUB-ASSEMBLY

    1. Using a small screwdriver, install a new snap ring at one end of the piston pin hole.

    2. G102126C02

      *a

      Front Mark

      Align the front marks of the piston and connecting rod cap.

    3. Apply a light coat of engine oil to the piston pin, and then push the piston pin into the hole of the piston and connecting rod.

    4. A198457

      Using a small screwdriver, install a new snap ring on the other end of the piston pin hole.

      Note:

      Do not change the combinations of the pistons and piston pins so that they can be returned to their original location when reassembling.

  5. INSTALL CONNECTING ROD BEARING

    1. A198458C03

      *a

      Oil Groove

      Align the connecting rod bearing and oil grooves, and then install the connecting rod bearing to the connecting rod.

      Note:

      Do not apply engine oil to the contact surfaces of the connecting rod, connecting rod cap or the back side of the connecting rod bearing.

  6. INSTALL PISTON RING SET

    1. A198459

      Install oil ring (expander) by hand.

    2. A198460C01

      *a

      Expander End

      *b

      Side Rail End

      Using a piston ring expander, install the oil ring (side rail) as shown in the illustration.

      Tip:

      The upper and lower oil rings are the same.

    3. G102127C03

      *a

      Code Mark

      V100135

      Upward

      Using a piston ring expander, install the No. 1 compression ring and No. 2 compression ring with the code marks as shown in the illustration.

      Part

      Code Mark

      No. 1 compression ring

      1R

      No. 2 compression ring

      2R

      Oil ring

      -

    4. A125827C02

      *1

      No. 1 Compression Ring

      *2

      No. 2 Compression Ring

      *a

      Oil Ring Position A

      *b

      Oil Ring Position B

      V100135

      Engine Front

      Position the piston rings so that the ring ends are as shown in the illustration.

      Note:

      Make sure that the gap in the oil ring is placed at either position A or B.

  7. INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

    1. G102128C02

      *a

      Front Mark

      Apply engine oil to the cylinder walls, pistons and surfaces of the connecting rod bearings.

    2. Check that the gap in the piston ring is positioned correctly.

    3. Check the front marks. Using a piston ring compressor, install the piston with pin sub-assembly with connecting rod.

    4. G102129C02

      *a

      Front Mark

      Check that the connecting rod and connecting rod cap are in the correct combination and that the front marks are facing correctly, and then install the connecting rod cap to the connecting rod.

      Note:

      The connecting rods and connecting rod caps should be reinstalled in their original combinations.

    5. Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.

    6. A198448E01

      Using SST, temporarily tighten and then tighten the connecting rod bolts to the specified torque.

      09205-16011

      15 N*m

      153 kgf*cm

      11 ft.*lbf

    7. A286927C08

      *a

      Paint Mark

      V100136

      Engine Front

      Mark the front of the connecting rod bolts with paint.

    8. Tighten the connecting rod bolts by additional 90°.

    9. Check that each paint mark is now at a 90° angle to the front.

    10. Check that the crankshaft turns smoothly.

  8. INSTALL TUBE CONNECTOR

    A194556C02

    *a

    Adhesive

    1. Apply adhesive to 2 or 3 threads of the tube connector.

      Adhesive

      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    2. A198471

      Using a 14 mm deep socket wrench, install the tube connector.

      25 N*m

      255 kgf*cm

      18 ft.*lbf