TIRE PRESSURE WARNING SYSTEM, Diagnostic DTC:B1247
| DTC Code | DTC Name |
|---|---|
| B1247 | Tire Pressure Monitor Receiver Communication Stop |
DESCRIPTION
The main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver are connected using 2 direct lines that they use to communicate with each other.
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
Note |
|---|---|---|---|---|
B1247 |
Tire Pressure Monitor Receiver Communication Stop |
In diagnostic mode, an applicable RDA signal cannot be received within 10 seconds after a PRG signal is sent from the main body ECU (multiplex network body ECU). |
|
This DTC is for main body ECU (multiplex network body ECU) |
WIRING DIAGRAM
CAUTION / NOTICE / HINT
When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.
It is necessary to perform initializationClick hereafter registrationClick hereof the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
PROCEDURE
CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)
Disconnect the L70, L88 or Q15 tire pressure warning ECU and receiver connector.
Disconnect the E22 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance
Table 1. for Sedan: Tester Connection
Condition
Specified Condition
L70-4 (RDA2) - E22-16 (RDA)
Always
Below 1 Ω
L70-4 (RDA2) or E22-16 (RDA) - Body ground
Always
10 kΩ or higher
Table 2. for Hatchback: Tester Connection
Condition
Specified Condition
L88-4 (RDA2) - E22-16 (RDA)
Always
Below 1 Ω
L88-4 (RDA2) or E22-16 (RDA) - Body ground
Always
10 kΩ or higher
Table 3. for Wagon: Tester Connection
Condition
Specified Condition
Q15-4 (RDA2) - E22-16 (RDA)
Always
Below 1 Ω
Q15-4 (RDA2) or E22-16 (RDA) - Body ground
Always
10 kΩ or higher
Result
Proceed to
OK
NG
NG REPAIR OR REPLACE HARNESS OR CONNECTOR
CHECK HARNESS AND CONNECTOR (POWER SOURCE OF TIRE PRESSURE WARNING ECU AND RECEIVER)
-
*A
for Sedan
*B
for Hatchback
*C
for Wagon
*a
Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)
Measure the resistance according to the value(s) in the table below.
Standard Resistance
Table 4. for Sedan: Tester Connection
Condition
Specified Condition
L70-12 (GND) - Body ground
Always
Below 1 Ω
Table 5. for Hatchback: Tester Connection
Condition
Specified Condition
L88-12 (GND) - Body ground
Always
Below 1 Ω
Table 6. for Wagon: Tester Connection
Condition
Specified Condition
Q15-12 (GND) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
Standard Voltage
Table 7. for Sedan: Tester Connection
Condition
Specified Condition
L70-1 (IG) - Body ground
Ignition switch ON
10 to 16 V
Table 8. for Hatchback: Tester Connection
Condition
Specified Condition
L88-1 (IG) - Body ground
Ignition switch ON
10 to 16 V
Table 9. for Wagon: Tester Connection
Condition
Specified Condition
Q15-1 (IG) - Body ground
Ignition switch ON
10 to 16 V
Result
Proceed to
OK
NG
NG REPAIR OR REPLACE HARNESS OR CONNECTOR
-
REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
Replace the tire pressure warning ECU and receiver.
for Sedan:Click here
for Wagon:Click here
for Hatchback:Click here
Result
Proceed to
NEXT
CHECK DTC OUTPUT
Clear the DTCs.
Body Electrical > Main Body > Clear DTCs
Turn the ignition switch off.
Turn the ignition switch to ON.
Check for DTCs.
Body Electrical > Main Body > Trouble Codes
OK
DTC B1247 is not output.
Result
Proceed to
OK
NG
OK END