ECD SYSTEM(w/o Glow Plug Controller), Diagnostic DTC:P0236,P0237 and P0238

DTC Code DTC Name
P0236 Turbocharger / Supercharger Boost Sensor "A" Circuit Range / Performance
P0237 Turbocharger / Supercharger Boost Sensor "A" Circuit Low
P0238 Turbocharger / Supercharger Boost Sensor "A" Circuit High

DESCRIPTION

A199024E02

The diesel turbo pressure sensor detects the intake manifold pressure. The ECM determines the basic injection duration and injection advance timing based on the voltage output from the diesel turbo pressure sensor.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

P0236

Turbocharger / Supercharger Boost Sensor "A" Circuit Range / Performance

The diesel turbo pressure sensor output differs from atmospheric pressure sensor output by more than the threshold for 0.5 seconds or more after ignition switch is turned ON to off.

(1 trip detection logic)

  • Open or short in diesel turbo pressure sensor circuit

  • Diesel turbo pressure sensor

  • ECM

Comes on

DTC stored

P0237

Turbocharger / Supercharger Boost Sensor "A" Circuit Low

Short in diesel turbo pressure sensor circuit for 5 seconds or more.

(1 trip detection logic)

  • Short in diesel turbo pressure sensor circuit

  • Diesel turbo pressure sensor

  • ECM

Comes on

DTC stored

P0238

Turbocharger / Supercharger Boost Sensor "A" Circuit High

Open in diesel turbo pressure sensor circuit for 1.5 seconds or more.

(1 trip detection logic)

  • Open in diesel turbo pressure sensor circuit

  • Diesel turbo pressure sensor

  • ECM

Comes on

DTC stored

Table 1. DTC Detection Drive Pattern

DTC No.

DTC Detection Drive Pattern

P0236

With a warm engine, turn the ignition switch from ON to off and wait for 30 seconds or more

P0237

10 seconds have elapsed since ignition switch turned ON.

P0238

5 seconds have elapsed since ignition switch turned ON.

Table 2. Related Data List

DTC No.

Data List

P0236

  • MAP

  • Atmosphere Pressure

P0237

P0238

Tip:

When DTC P0236, P0237 and/or P0238 are stored, check the intake manifold pressure by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / MAP.

Reference

Intake Manifold Pressure (MAP)

Malfunction

Approximately 0 kPa

  • Short in PIM circuit

  • Open in VC circuit

250 kPa (1875 mm Hg, 73.8 in. Hg) or higher

  • Short in VC to PIM circuits

  • Open in PIM circuit

  • Open in EPIM circuit

WIRING DIAGRAM

A293483E02

CAUTION / NOTICE / HINT

Note:

When replacing the ECM, perform ECM Initialization and Registration.

Click hereClick here

Tip:
  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing a new ECM, perform all of the initialization and registration procedures for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE

  1. READ VALUE USING GTS (MAP AND ATMOSPHERE PRESSURE)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.

      Powertrain > Engine and ECT > Data List

      Tester Display

      Atmosphere Pressure

      MAP

    4. Compare the values when the ignition switch is ON.

      Standard

      Difference between the MAP and the Atmosphere Pressure is less than 7 kPa.

      Tip:

      Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. Atmospheric pressure varies with the weather.

    Result

    Proceed to

    OK

    NG

    NG

    CHECK HARNESS AND CONNECTOR (DIESEL TURBO PRESSURE SENSOR - ECM)Click here

    OK
  2. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch to ON and wait for 10 seconds or more.

    5. Start the engine and warm it up.

    6. Turn the ignition switch off. Wait 30 seconds or more, and restart the engine.

    7. Turn the GTS on.

    8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

      Powertrain > Engine and ECT > Trouble Codes

    9. Confirm that the DTC is not output again.

    Result

    Proceed to

    NEXT

    NEXT

    END

  3. CHECK HARNESS AND CONNECTOR (DIESEL TURBO PRESSURE SENSOR - ECM)

    1. Disconnect the diesel turbo pressure sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      B126-2 (PIM) - A101-13 (PIM)

      Always

      Below 1 Ω

      B126-3 (VC) - A101-14 (VPIM)

      Always

      Below 1 Ω

      B126-1 (E) - A101-15 (EPIM)

      Always

      Below 1 Ω

      B126-2 (PIM) or A101-13 (PIM) - Body ground

      Always

      10 kΩ or higher

      B126-3 (VC) or A101-14 (VPIM) - Body ground

      Always

      10 kΩ or higher

      B126-1 (E) or A101-15 (EPIM) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTORClick here

    OK
  4. CHECK TERMINAL VOLTAGE (VC VOLTAGE)

    A200310C03

    *a

    Front view of wire harness connector

    (to Diesel Turbo Pressure Sensor)

    1. Disconnect the diesel turbo pressure sensor connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      B126-3 (VC) - B126-1 (E)

      Ignition switch ON

      4.75 to 5.25 V

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE ECMClick here

    OK
  5. REPLACE DIESEL TURBO PRESSURE SENSOR

    1. Replace the diesel turbo pressure sensor.

      Click hereClick here

    Result

    Proceed to

    NEXT

    NEXT
  6. CHECK WHETHER DTC OUTPUT RECURS

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch to ON and wait for 10 seconds or more.

    5. Start the engine and warm it up.

    6. Turn the ignition switch off. Wait 30 seconds or more, and restart the engine.

    7. Turn the GTS on.

    8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    9. Read the DTCs.

      Powertrain > Engine and ECT > Trouble Codes

      Result

      Result

      Proceed to

      DTC P0236, P0237 and/or P0238 is output

      A

      DTC is not output

      B

    B

    END

    A
  7. REPLACE ECM

    1. Replace the ECM.

      Click here

    Result

    Proceed to

    NEXT

    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  8. REPAIR OR REPLACE HARNESS OR CONNECTOR

    Result

    Proceed to

    NEXT

    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here