TIRE PRESSURE WARNING SYSTEM, Diagnostic DTC:B1247

DTC Code DTC Name
B1247 Tire Pressure Monitor Receiver Communication Stop

DESCRIPTION

The main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver are connected using 2 direct lines that they use to communicate with each other.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Note

B1247

Tire Pressure Monitor Receiver Communication Stop

In diagnostic mode, an applicable RDA signal cannot be received within 10 seconds after a PRG signal is sent from the main body ECU (multiplex network body ECU).

  • Tire pressure warning ECU and receiver

  • Wire harness or connector

  • Main body ECU (multiplex network body ECU)

This DTC is for main body ECU (multiplex network body ECU)

WIRING DIAGRAM

C287871E01

CAUTION / NOTICE / HINT

Note:
  • When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

  • It is necessary to perform initializationClick hereafter registrationClick hereof the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.

Tip:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE

  1. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)

    1. Disconnect the L70 tire pressure warning ECU and receiver connector.

    2. Disconnect the E22 main body ECU (multiplex network body ECU) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      L70-4 (RDA2) - E22-16 (RDA)

      Always

      Below 1 Ω

      L70-4 (RDA2) or E22-16 (RDA) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  2. CHECK HARNESS AND CONNECTOR (POWER SOURCE OF TIRE PRESSURE WARNING ECU AND RECEIVER)

    1. C250865C20

      *a

      Front view of wire harness connector

      (to Tire Pressure Warning ECU and Receiver)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      L70-12 (GND) - Body ground

      Always

      Below 1 Ω

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      L70-1 (IG) - Body ground

      Ignition switch ON

      10 to 16 V

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  3. REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

    1. Replace the tire pressure warning ECU and receiver.

      Click here

    Result

    Proceed to

    NEXT

    NEXT
  4. CHECK DTC OUTPUT

    1. Clear the DTCs.

      Click here

      Body Electrical > Main Body > Clear DTCs

    2. Turn the ignition switch off.

    3. Turn the ignition switch to ON.

    4. Check for DTCs.

      Click here

      Body Electrical > Main Body > Trouble Codes

      OK

      DTC B1247 is not output.

    Result

    Proceed to

    OK

    NG

    OK

    END

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    for LHD

    Click here

    for RHD

    Click here