LIGHTING SYSTEM Interior Light Circuit

DTC Code DTC Name
Interior Light Circuit

DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the following lights:

  • Map Light Assembly

  • No. 1 Room Light Assembly*1

Tip:

The DOME CUT relay supplies power to the interior lights. If all the lights that use power from the DOME CUT relay do not turn on, check the interior light power source circuit first.

Click here

  • *1: w/ Room Light

WIRING DIAGRAM

E262990E01

PROCEDURE

  1. PERFORM ACTIVE TEST USING GTS

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Active Test.

    5. Perform the Active Test according to the display on the GTS.

      Body Electrical > Main Body > Active Test

      Tester Display

      Measurement Item

      Control Range

      Diagnostic Note

      Illuminated Entry System

      Lights up the lights that are controlled by the illuminated entry system.*1

      ON or OFF

      -

      • *1: Refer to System Description for the lights that are controlled by the illuminated entry system.

        Click here

      Body Electrical > Main Body > Active Test

      Tester Display

      Illuminated Entry System

      Result

      Result

      Proceed to

      All lights that are controlled by the illuminated entry system come on.

      A

      • All lights that are controlled by the illuminated entry system do not come on (w/ Room Light (for Slide Switch Type))

      • All lights that are controlled by the illuminated entry system do not come on (w/o Room Light)

      B

      All lights that are controlled by the illuminated entry system do not come on (w/ Room Light (for Push Switch Type))

      C

    A

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

    B

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MAP LIGHT ASSEMBLY)Click here

    C
  2. INSPECT MAP LIGHT ASSEMBLY

    1. Remove the map light assembly.

      Click hereClick here

    2. Inspect the map light assembly.

      Click here

      OK

      Map light assembly is normal.

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE MAP LIGHT ASSEMBLY

    OK
  3. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MAP LIGHT ASSEMBLY)

    1. Disconnect the 3C instrument panel junction block assembly connector.

    2. Disconnect the O6 No. 1 room light assembly connector.*1

      • *1: w/ Room Light (for Slide Switch Type)

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      3C-54 - O8-3 (CTY)

      Always

      Below 1 Ω

      3C-54 - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  4. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

    1. Remove the instrument panel junction block assembly.

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

    3. Measure the resistance according to the value(s) in the table below.

      E258624C04

      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      -

      -

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      3C-54 - MB-1 (ILE)

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY